ICF C1iPMK2

Transcript

1 Important Safety Instructions Owner’s Record 15 3-873-060- (1) Read these instructions. 1) Connecting the antenna Precautions The model number and the serial number are located 2) Keep these instructions. on the rear exterior. Operate the unit on the power sources specified in  3) Heed all warnings. Record the serial number in the space provided below. “Specifications” . To connect the AM loop antenna Refer to them whenever you call upon your Sony 4) Follow all instructions. To disconnect the power cord (mains lead), pull it  dealer regarding this product. The shape and the length of the antenna is designed to 5) Do not use this apparatus near water. out by the plug, not the cord. receive AM signals. Do not dismantle or roll up the 6) Clean only with dry cloth. Model No. ICF-C1iPMK2 The unit is not disconnected from the AC power  antenna. 7) Do not block any ventilation openings. Serial No. source (mains) as long as it is connected to the wall Install in accordance with the manufacturer’s outlet, even if the unit itself has been turned off. 1 Remove only the loop part from the plastic instructions. Do not leave the unit in a location near a heat  stand. For customers who purchased this product in the 8) Do not install near any heat sources such as source, such as a radiator or airduct, or in a place USA 2 Set up the AM loop antenna. radiators, heat registers, stoves, or other apparatus subject to direct sunlight, excessive dust, mechanical Please register this product on line at (including amplifiers) that produce heat. vibration, or shock. . http://www.sony.com/productregistration 9) Do not defeat the safety purpose of the polarized Allow adequate air circulation to prevent internal  Proper registration will enable us to send you or grounding-type plug. A polarized plug has two heat build-up. Do not place the unit on a surface (a periodic mailings about new products, services, FM/AM Clock Radio blades with one wider than the other. A grounding rug, blanket, etc.) or near materials (a curtain) that and other important announcements. Registering type plug has two blades and a third grounding might block the ventilation holes. your product will also allow us to contact you in prong. The wide blade or the third prong are ICF-C1iPMK2 Should any solid object or liquid fall into the unit,  the unlikely event that the product needs provided for your safety. If the provided plug does 3 Connect the cords to the AM antenna unplug the unit and have it checked by qualified adjustment or modification. Thank you. not fit into your outlet, consult an electrician for personnel before operating it any further. terminals. replacement of the obsolete outlet. To clean the casing, use a soft cloth dampened with The cords (A and B) can be connected to either  Protect the power cord from being walked on or 10) a mild detergent solution. terminal. pinched particularly at plugs, convenience WARNING Operating Instructions receptacles, and the point where they exit from the NOTES ON LITHIUM BATTERY Insert the cord while To reduce the risk of fire or electric shock, do not apparatus. Wipe the battery with a dry cloth to assure a good pushing down the  expose this apparatus to rain or moisture. 11) Only use attachments/accessories specified by the contact. terminal clamp. To reduce the risk of electrical shock, do not open manufacturer. Be sure to observe the correct polarity when the cabinet. Refer servicing to qualified  Use only with the cart, stand, tripod, bracket, or 12) installing the battery. personnel only. table specified by the manufacturer, or sold with To reduce the risk of fire, do not cover the ventilation Do not hold the battery with metallic tweezers,  the apparatus. When a cart is used, use caution of the apparatus with newspapers, tablecloths, otherwise a short-circuit may occur. when moving the cart/apparatus combination to curtains, etc. And do not place lighted candles on the avoid injury from tip-over. apparatus. If you have any questions or problems The apparatus shall not be exposed to dripping or concerning your unit, please consult your nearest splashing and that no objects filled with liquids, such Sony dealer. as vases, shall be placed on the apparatus. Do not install the appliance in a confined space, such Specifications as a bookcase or built-in cabinet. 4 Unplug this apparatus during lightning storms or 13) Make sure the AM loop antenna is As the main plug is used to disconnect the unit from when unused for long periods of time. connected firmly by pulling softly. Time display the mains, connect the unit to an easily accessible AC Refer all servicing to qualified service personnel. 14) 12-hour System outlet. Should you notice an abnormality in the unit, Dream Machine is a trademark of Sony Corporation. Servicing is required when the apparatus has been Adjusting the AM loop antenna disconnect the main plug from the AC outlet damaged in any way, such as power-supply cord or Frequency range Find a place and an orientation that provide good immediately. plug is damaged, liquid has been spilled or objects reception. Channel step Frequency Band have fallen into the apparatus, the apparatus has Do not place the AM loop antenna near the unit or  You are cautioned that any changes or 87.5 – 108 MHz FM 0.1 MHz been exposed to rain or moisture, does not operate other AV equipment, as noise may result. modifications not expressly approved in this manual normally, or has been dropped. 530 – 1 710 kHz 10 KHz AM could void your authority to operate this equipment. If you use an external polarized AM antenna, be sure  No Power No Problem is a trademark of Sony Corporation. terminal. The  to connect the ground cord to the For the state of california, USA only Speaker supplied AM antenna cord has no polarity. Perchlorate Material –special handling may apply, See Approx. 5.1 cm (2 inches) dia., 12 Ω www.dtsc.ca.gov/hazardouswaste/perchlorate Tip Power output Perchlorate Material: Lithium battery contains Adjust the direction of the AM loop antenna for best 3 W + 3 W (at 10% harmonic distortion) perchlorate AM broadcast sound. Power requirements 120 V AC, 60 Hz Features For clock backup: 3 V DC, one CR2032 battery Dual alarm FM/AM Clock radio with iPod dock. ©2008 Sony Corporation Printed in China  Dimensions Various type of alarms- iPod, radio and buzzer. Approx. 300 × 130 × 139 mm (w/h/d)  13 1 1 / 16 (11 / inches) incl. projecting parts 2 × 5 8 / × 5 Automatic time set — When you plug the clock in  and controls for the first time, the current time will be shown in the display. Mass This symbol is intended to alert the user Automatic Daylight Saving Time/Summer time  Approx. 1.8 kg (3 lb 15.4 oz) incl. CR2032 battery to the presence of uninsulated “dangerous adjustment. voltage” within the product’s enclosure Supplied accessories CLOCK button to display month, day and year.  that may be of sufficient magnitude to Remote commander (1) Brightness control (High/Middle/Low).  constitute a risk of electric shock to Audio connecting cable (1) No Power No Problem alarm system to keep the  persons. AM loop antenna (1) ™ clock and the alarm operating during a power interruption with a CR2032 battery installed. This symbol is intended to alert the user Design and specifications are subject to change to the presence of important operating without notice. and maintenance (servicing) instructions in the literature accompanying the Troubleshooting appliance. Should any problem occur with the unit, make the Class II equipment symbol This symbol following simple checks to determine whether or not indicates that the unit has a double servicing is required. insulation system. If the problem persists, consult your nearest Sony dealer. INFORMATION This equipment has been tested and found to comply The clock displays “AM 12:00” due to a power with the limits for a Class B digital device, pursuant to interruption. Part 15 of the FCC Rules. These limits are designed to The battery is low. Replace the battery. Remove the  provide reasonable protection against harmful old battery and install a new one. interference in a residential installation. This When daylight saving time begins, the clock does equipment generates, uses and can radiate radio not employ the daylight saving time frequency energy and, if not installed and used in automatically. accordance with the instructions, may cause harmful Make sure the clock is set correctly. interference to radio communications. However, there  is no guarantee that interference will not occur in a Press and hold CLOCK TIME ZONE/ALARM and  particular installation. If this equipment does cause simultaneously for at least two seconds to DISPLAY harmful interference to radio or television reception, employ the DST function. which can be determined by turning the equipment The alarm does not sound at the preset alarm off and on, the user is encouraged to try to correct the time. interference by one or more of the following measures: Has the desired alarm been activated? (i.e., Does the — Reorient or relocate the receiving antenna.  ) indicator light up?) B ALARM A (or — Increase the separation between the equipment and receiver. The radio or iPod alarm is activated but no sound Connect the equipment into an outlet on a circuit — comes on at the preset alarm time. different from that to which the receiver is Has been adjusted? VOLUME  connected. Consult the dealer or an experienced radio/TV — There is no sound from the iPod. technician for help. Make sure the iPod is securely connected.  Adjust the VOLUME . WARNING  Danger of explosion if battery is incorrectly  The iPod cannot be operated with this unit. replaced. Replace only with the same or equivalent Make sure the iPod is securely connected.  type. Replace the battery for the clock backup with a Sony  The iPod cannot be charged. CR2032 lithium battery, and the battery for the Make sure the iPod is securely connected.  remote commander with a Sony CR2025 lithium battery. Use of another battery may present a risk of fire or explosion. Battery may explode if mistreated. Do not recharge,  disassemble or dispose of in fire. Do not expose the battery to excessive heat such as  direct sunlight, fire or the like. Dispose of used battery promptly. Keep away from  children. This unit includes a preinstalled Sony Lithium battery (CR2032) as back-up power source for the clock, which is preset to EST/EDT (Eastern Standard Time/Daylight Time) at the factory. And this battery is considered part of the product. 15 (1) ICF-C1iPMK2_U2 [US] 3-873-060-

2 Note Do not pull on the rear support strongly as it cannot Tuning into a preset station To deactivate the alarm  During the shipment and your first use, a clock error be detached from the unit and may cause a About the backup ) to turn off the Press ALARM SET A (or B may occur. In this case, refer to “Setting the clock and 1 Press to turn on the radio. RADIO ON malfunction. date” to set the correct time. (or ALARM A ) indicator from the display. B To use an iPod, refer to the user’s guide of your iPod. battery 2  Press one of the PRESET TUNING buttons Before disconnecting the iPod, pause playback.  where the desired station is stored. Note on alarm in the event of a power To keep good time, as a backup power source, this unit When daylight saving time interruption has one CR2032 battery inside of the unit in addition 3 VOLUME . Adjust volume using Tip iPod nano (summer time) begins When the alarm sound is set to RADIO or iPod, it  to the house current. Apple’s iPod Universal Dock Adapter can be used with 1st generation iPod iPod will change to BUZZER automatically. This model employs the Automatic Daylight Saving The battery keeps the clock and the alarm operating in this unit. 4th generation 4th generation If the backup battery is exhausted, the alarm will not Time/Summer Time adjustment. The DST indicator in the event of a power interruption.  (color display) Setting the alarm work in the event of power interruption. Replace the the display appears in the display at the beginning of Note that the backlight will not light up during a To use the unit as a battery battery periodically. the daylight saving time (summer time), and power interruption. The dual alarm function allows you to set two alarm disappears at the end of it. charger programs (ALARM A and ALARM B). Daylight saving time begins at: 2:00 AM on the  Knowing when to replace the The alarm time can be set for each program and the You can use the unit as a battery charger. second Sunday of March. alarm sound is selectable from RADIO, BUZZER or The charging begins when the iPod is placed on the Setting the sleep timer battery Standard time begins at: 2:00 AM on the first iPod.  connector. If a power interruption occurs when the battery is Sunday of November. You can fall asleep to the sound using the built-in The charging status appears in the iPod display. For Notes weak, the brightness of characters in the display sleep timer that turns off the unit automatically after a details, see the user’s guide of your iPod. Before setting the alarm, make sure to set the clock  darkens. If the battery runs out during the iPod mini preset duration. To deactivate the Automatic DST/ (see “Setting the clock and date”). interruption, the current time and alarm functions will On copyrights Summer Time adjustment during be initialized. The factory setting alarm time is “AM 12:00”. 1 Press SLEEP while the unit is turned on.  Notes iPod is a trademark of Apple Inc., registered in the  SLEEP appears in the display. To set the radio alarm, first tune in to a station  The connector of the unit is for sole use for iPod. the daylight saving time (summer  U.S. and other countries. Replace the battery with a Sony CR2032 lithium (see “Playing the radio”). When you use the devices do not match with the 2 to set the sleep timer duration. SLEEP Press time) period. battery. Use of another battery may present a risk of iPhone is a trademark of Apple Inc.  terminal of AUDIO IN connector, connect it to the SLEEP Each time you press , the duration changes fire or explosion. All other trademarks and registered trademarks are The Automatic DST/Summer Time adjustment can be  this unit with the supplied audio connecting cable. To set the alarm time as follows: and of their respective holders. In this manual, cancelled. Sony cannot accept responsibility in the event that  ® ™ To set ALARM A Replacing the backup battery marks are not specified. TIME ZONE/ALARM DISPLAY CLOCK and for Press data recorded to iPod is lost or damaged when using 1 more than two seconds. The Automatic DST/Summer Press ALARM SET A for a few seconds. an iPod connected to this unit. FM wire antenna 1 Keep the AC plug connected to the AC Time adjustment will be cancelled. To active the 2 TIME SET +/– Press to set the desired hour, The display returns to clock mode five seconds outlet, remove the screw that secures the Automatic DST/Summer Time adjustment again, 1 Put the iPod into the unit’s connector. Playing the radio after you have finished setting the duration setting and press . ALARM SET A repeat the same operation. battery compartment at the bottom of the and released SLEEP , and then the sleep timer 3 Press to set the desired TIME SET +/– —Manual tuning unit using a screwdriver, and remove the starts. . minute, and press ALARM SET A -   ) battery compartment. (See Fig. The unit will play for the duration you set, and 1 Press RADIO ON to turn on the radio. Setting the clock and 4 Press TIME SET +/– to set the desired alarm then shut off. AC power cord 2 The display shows the band and frequency. Insert a new battery in the battery mode (RADIO, BUZZER or iPod) and press side facing up.  compartment with the date To turn off the unit before the . ALARM SET A To remove the battery from the battery To change the setting manually, follow the procedure compartment, push it out from the side marked preset time 5 If you select the RADIO or iPod, press TIME from step 1 .  -  PUSH. (See Fig. ) SET +/– to set the wake up volume and . Press OFF 3 Insert the battery compartment back into 1 for more than 2 seconds. Press CLOCK 2 . press ALARM SET A Press RADIO ON repeatedly to select the The year will start to flash in the display. the unit and secure it with the screw. To use both sleep timer and alarm desired band. , follow the same steps above using ALARM B To set (See Fig. - )   2 – or TIME SET + Press until the correct year Each press changes the band as follows: You can fall asleep to the radio and also be awakened . instead of ALARM A ALARM B by the radio or buzzer alarm at the preset time. appears in the display. Note ALARM TIME A To change the display between and When you replace the battery, keep the AC plug 3 . CLOCK Press , press ALARM TIME B . TIME ZONE/ALARM DISPLAY 1 Set the alarm. (See “Setting the alarm”.) connected to a wall outlet. Otherwise, current time  and PRESET TUNING 3 button. There is a tactile dot on the VOLUME +,  / 4 FM1 and FM2 are the same frequency bands. 3 to set the month, day and Repeat steps 2 When using iPod touch/iPhone 2 Set the sleep timer. (See “Setting the sleep and alarms will be initialized if the replacement is not Adjust the rear support forward or backward and time. To use music stored in an iPod touch/iPhone to wake 3 – or to tune into the desired TUNING + Use completed within around one minute. timer”.) checking the back of the iPod fits snugly against After setting the minute the clock starts from up, put the iPod touch/iPhone into the unit first, station. the rear support to protect the connector. follow the steps above to set alarm time, and then 0 seconds. But if you do not set “Minute”, the clock The FM frequency advances or reverses in 0.1 If the time in the display is select the desired music. does not start from 0 second flat. MHz channel steps and the AM frequency in 10  Other useful functions incorrect after the battery is Pressing and holding – changes the year, or +  kHz channel steps. Notes month, day or time rapidly. changed (RESET) When you use the radio alarm, the timed alarm  4 . Adjust volume using VOLUME To get the MEGA Xpand effect While setting the clock, you must perform each step  sounds with the last broadcasting station tuned to Push the Reset switch with the pointed device. The To turn off the radio, press OFF .   within about 65 seconds, or the clock setting mode . “MEGA Xpand” appears in the Press MEGA Xpand before the power went off. When you set the radio Reset switch is in the small hole located in the battery will be cancelled. display. You can get the effect of expansion of the alarm, select the desired broadcasting station before compartment. sound field. To return to normal sound, press the turning the power off. button again. Improving the Notes To display the year and date The ALARM A (or B ) indicator flashes in the display  You cannot reset unless the lithium battery is  when the alarm sounds. CLOCK Press once for the date, and within reception installed. If a second alarm sounds during a first (or the  about 5 seconds press it again for the year. Set the clock again after the unit is reset. Connecting external  SNOOZE function is active), the second alarm takes FM: Extend the FM wire antenna fully to The display shows the date or year for about priority. increase reception sensitivity. Battery Warning 5 seconds and then changes back to the current time. equipment AM: Connect the supplied AM loop antenna The alarm function works as usual at the beginning  When the unit will be left unplugged for a long time, to the unit. Rotate the antenna and end day of the daylight saving time (summer remove the battery to avoid undue battery discharge To listen to sound horizontally for optimum reception. time). While the Automatic DST/Summer Time and damage to the unit from battery leakage. Setting the brightness adjustment is set, as a result, if the alarm is set at a CR2032 Keep away digital music player or mobile phone from 1 jack of the unit to AUDIO IN Connect the time skipped when the daylight saving time the AM loop antenna or the FM wire antenna, as this of the display the line out jack or headphone jack of the (summer time) begins, the alarm is skipped, or if the may lead to interference of reception. Preparing the remote alarm is set at a time overlapped when the daylight external equipment using the audio Three levels of brightness are available by saving time (summer time) ends, the alarm sounds Note connecting cable (supplied). commander . SNOOZE/BRIGHTNESS pressing twice.  When you are listening to the radio with an iPhone connected to the unit, interference with radio If the same alarm time is set for both alarm  Before using the card remote commander for the first reception may occur. (ALARM A and B), the ALARM A takes priority.  -  time, remove the insulation film. (See Fig. ) Tip To activate the alarm When to replace the battery If the FM broadcast is noisy, press FM MODE on the remote commander to turn off “STEREO” in the With normal use, the battery (CR2025) should last for After setting the alarm time, follow these steps: display. The radio becomes clearer although the sound Playing the iPod about six months. When the remote commander no ALARM SET A To activate the ALARM A , press becomes monaural. longer operates the unit, replace the battery with new You can enjoy iPod audio by connecting this unit. To 2 . to display ALARM A  / .  Press   ones. (See Fig. ) - use an iPod, refer to the user’s guide of your iPod. The iPod begins to play automatically. To activate the ALARM B , press ALARM SET B Notes You can operate the connected iPod by the unit or . ALARM B to display Presetting your Do not charge the battery. Compatible iPod models  iPod buttons. When you are not going to use the remote Notes  The compatible iPod models are as follows. Update favourite station Press To commander for a long time, remove the battery to The alarm sounds at the set time even if the unit is  your iPod to use the latest software before you use it. Turn off the iPod OFF , or press and hold  avoid any damage caused by leakage and corrosion. on. —Preset tuning Pause playback   / Make sure the iPod is installed correctly after setting  You can preset up to 10 stations in FM (5 stations in  To resume play, press it again. the iPod alarm. FM1, 5 stations in FM2), and 5 stations in AM. Go to the next  Setting the clock for the 2 to display “AUDIO IN”. Press AUDIO IN Notes on using iPod touch/iPhone track Presetting a station If you set the iPod alarm while iPod touch/iPhone 3 Play the equipment connected to the  Go back to the  first time music is playing, and then turn the unit power off,  previous track 1 Follow steps 4 to 1 in “Playing the Radio” jack. AUDIO IN when the alarm time comes on, the alarm music will This unit is preset to the current date and time at the Locate a point (forward) or   and manually tune into the station you wish 4 Adjust the volume using VOLUME . resume from the point where the power was turned iPod nano iPod nano factory, and is powered by the back up battery. All you while listening to (backward) while playing and to preset. 4th generation 5th generation off. need to do the first time is just plug it in and select the sound hold it until you find the point. iPod touch (video) (video camera) To return to the radio 2 Even if the iPod alarm setting is complete, if you your time zone. PRESET Press and hold the desired  2nd generation Locate a point   (forward) or turn the iPod touch/iPhone power off before the button for more than two seconds TUNING RADIO ON . Press while observing (backward) in pause and hold it 1 Plug in the unit. unit, the iPod alarm will not work. The frequency is shown in the display. the display until you find the point. for registration. 2 for more then two Press TIME ZONE After the preset has finished, the preset number Go back to the MENU * To doze for a few more minutes To return to the iPod seconds. appears on the display. previous menu Area number “2” appears in the display. Select a menu . SNOOZE/BRIGHTNESS Press /  *  Press .   / To preset AM 1 260 kHz onto preset Example: CR2025 If you live in the Eastern Time zone, you do not item or a track for The sound turns off but will automatically come on button. 2  iPod nano need to adjust the area setting. playback again after about 5 minutes. To stop listening 3rd generation The maximum length of the snooze time is Execute the ENTER * Area number Time zone (video) 40 minutes. selected menu or iPod classic OFF , and stop playback on the connected Press 1 Atlantic Standard/Daylight Time iPod touch the playback  unit. 1st generation 2 Eastern Standard/Daylight Time To stop the alarm (default) * These operations are available only when using the a few seconds after  supplied remote commander. OFF Press to turn off the alarm. 3 Central Standard/Daylight Time The alarm will come on sound again at the same time Mountain Standard/Daylight Time 4 Notes the next day. Pacific Standard/Daylight Time 5 When placing or removing the iPod, keep it straight  is not pressed, the buzzer alarm sounds OFF If and parallel with the rear support. Yukon Standard/Daylight Time 6 continuously for about 3 minutes, and then it stops automatically. Do not carry the unit with an iPod set on the 7 Hawaiian Standard/Daylight Time  To preset another station, repeat these steps. OFF is The RADIO and iPod sound continuously until connector. Doing so may cause a malfunction. iPod nano There is a tactile dot on the VOL +, To change the preset station, tune into the desired pressed. 2nd generation iPod When placing or removing the iPod, brace the unit and PRESET + button.  /  ,  3 – repeatedly until the or Press TIME SET +  to station and hold down the PRESET TUNING 1 iPhone (aluminium) 5th generation with one hand and take care not to press the controls desired number appears. 5 button. The new station will replace the previous (video) of the iPod by mistake. station on the preset button. 4 Press TIME ZONE to complete the setting. 15 (1) ICF-C1iPMK2_U2 [US] 3-873-060-

Related documents