FM1161B NAEN

Transcript

1 nVent CADDY Speed Link Universal Support System

2 HVAC applications Concrete Structure Attachments Hanging Solutions 2 | nVent.com/CADDY

3 HVAC Steel Structure Attachments nVent.com/CADDY | 3

4 Electrical & Datacom applications Concrete Structure Attachments Hanging Solutions 4 | nVent.com/CADDY

5 Electrical & Datacom Steel Structure Attachments nVent.com/CADDY | 5

6 WIRE ROPE SUPPORT SYSTEMS AN EXAMIMATION OF THE UNIQUE ADVANTAGES OF WIRE ROPE SUPPORT SYSTEMS IN MECHANICAL, ELECTRICAL AND DATACOM INSTALLATIONS. Benefits of a Wire Rope Support System Cable support systems offer a unique combination of advantages that benefit almost any contracting project. CONTRACTORS USE WIRE ROPE SUPPORT SYSTEMS BECAUSE THEY ARE LIGHTWEIGHT, SAFE, EFFECTIVE AND EASY TO INSTALL. WHILE MOST COMPARABLE METHODS ARE DESIGNED FOR A SPECIFIC APPLICATION, WIRE ROPE SYSTEMS EXCEL IN FOUR KEY AREAS: ADAPTABILITY: Unlike other support systems, wire rope can be easily adapted to work with a variety of applications. The system appears very simple, but can be easily modified to hang rectangular duct, spiral duct, piping, basket tray, light fixtures and almost any other application that hangs from the ceiling. When cable supports are used for multiple applications on a jobsite, it greatly reduces the number of different products and tools that are needed, reduces waste, and simplifies purchasing. Steel cable is incredibly flexible and allows for assemblies to be supported from a variety of angles. Unlike other FLEXIBILITY: methods that can be rigid and demand timely measurement, wire rope gives installers more slack when installing. SPEED: Traditional support methods can make installing large assemblies very difficult. However, wire rope systems can be very quickly installed. Other hanging methods like jack chain, metal strap and threaded rod, need to be measured, cut, and installed using several tools. Wire rope systems are much easier to adjust and eliminate many of the time consuming tasks required for other installation methods. Installers can easily make fine adjustments with a wire rope support system by unlocking the wire from the locking ADJUSTABILITY: device, moving the assembly and relocking the wire. Additionally, even load distribution between several supports can be easily and quickly checked by measuring cable tension the same way a contractor would measure tension on a V-Belt. | nVent.com/CADDY 6

7 nVent CADDY Speed Link SLK Locking Device WHY CHOOSE THE SLK? MARKET CONDITIONS With so many wire rope support systems on the market, it can be difficult to identify the proper system to use in any situation. Wire rope systems are lightweight, flexible, adaptable, and easy to use, but it is also important to know which specific product is most effective. THE NVENT CADDY SOLUTION The goal of the nVent CADDY development team is to provide the best products on the market. The Speed Link SLK locking device is designed to combine a unique collection of features to provide the most value to the end user. Specifically, there are three main features and three main applications that make the Speed Link SLK Locking Device different from any other wire rope support system on the market. FEATURES : The inside of the device has two jaws gripping the wire as opposed to the much more common single-cam device. Double-Jaw : The device can be easily installed without keys or tools. Keyless Installation Easily Used with Gloves : The Release tube are big enough to be used while wearing gloves, unlike other smaller devices on the market. APPLICATIONS The unique design of Speed Link SLK Locking Device allows for special applications: Speed Link Competitive Advantages Competitor Competitor Competitor Competitor Description Part Number "Z" Application "B" "G" "D" Speed Link • Joining two pieces of wire * * Splice      • Practical when working with wire spools or spool kits • Increased load rating • Ideal when working with wire spools * * Infinite Loop      • Only requires one locking device per drop • Useful in tight spaces • Placing the locking device closer to the load makes it easier to hide Low Level of 90° ? 39° ? 60° • The higher the maximum Concealment angle, the closer the device can be to the service • Useful in tight spaces * Not specified on technical documents [but not advertized either] ? Not specified on technical documents but always shown with an angle lower than 90 degrees | 7 nVent.com/CADDY

8 Speed Link Universal Support System Speed Link is a universal support system designed to reduce installation time. A cost-effective alternative to jack chain, threaded rod, strut and strut nuts, this innovative system has the versatility to meet virtually all your support needs. • Systems include locking device, wire rope, and specialty end fitting • Strong, yet flexible, wire rope • Selection of locking devices for different applications and load requirements Extensive range of end fittings for various types of structural attachments • • Allows objects to be hung at a variety of angles, even from sloped ceilings • Works with an assortment of CADDY fasteners Speed Link Speed Link PAGES PAGE 22 9-21 Slk System Ld System Versatile wire rope system featuring Light duty wire rope system; ideal for hanging keyless adjustment across a broad range light-duty fixtures, ductwork, speakers, alarm sensors, signage and pipes in applications of applications; ideal for hanging ductwork, pipe and tube, cable tray, lighting, conduit, that require all stainless steel components for a greater corrosion resistance. strut profiles and signage. PAGE PAGE Speed Link Speed Link Extensions 23-29 Sls System 30-33 Versatile wire rope system that attaches Wire rope extensions with specialty end directly to metal framing channels fittings to combine with other Speed Link systems. without the use of tools; ideal for hanging strut-based applications, ceiling fan units or cable tray. PAGES Speed Link Locking Speed Link PAGE 34-37 Devices And Wire Rope Accessories 38-41 Kit includes spool of Speed Link steel wire Accessories for Speed Link wire rope systems. and Speed Link SLK locking devices | nVent.com/CADDY 8

9 Speed Link SLK Device AESTHETICAL FEATURES EASE OF USE FEATURES SAFETY FEATURES Arrows on the device clearly Low-profile locking device provides a Keyless release tubes are positive aesthetic to a finished project demonstrate the correct designed to allow safe and easy direction to push the wire adjustment, even while wearing bulky gloves Speed Link SLK System Two jaws grip the wire inside Speed Link is lighter, the device, holding the wire faster to install, easier to more securely than single-cam transport and generates less devices common among most waste than alternative competitors. This rare gripping hanging methods mechanism allows it to be used in unique applications such as splicing/joining two wires, infinite loop etc. Available in pre-cut lengths with 11 end-fittings or in bulk with spools of wire to adapt to UL Listing on all 11 end fittings the end-users’ needs and for pre-cut lengths, SMACNA applications approved for hook and loop end fittings. Intertek Load Test report available upon request. Two tool-free locking devices are available for three wire sizes: • SLK2 compatible with 1.5mm and 2mm wire • SLK3 compatible with 3mm wire The color of the line corresponds to the larger goal of each feature: SAFETY FEATURES The locking device can accommodate AESTHETICAL FEATURES wire rope at up to 90 degrees, EASE OF USE FEATURES allowing it to be positioned closer to the load than other locking devices on the market, hiding it from view and creating a much more aesthetically pleasing installation. | 9 nVent.com/CADDY

10 Speed Link SLK System Speed Link SLK System The Speed Link SLK system provides a versatile overhead support solution that is easy to adjust and installs quickly to almost any structure. The system supports a wide range of applications, including ductwork, pipe and tube, cable tray, lighting, conduit, strut profiles and signage from overhead structural building members. It is available with a variety of specialty end fittings for the most common building structure types, a range of wire rope diameters and lengths, and includes a unique keyless locking device. • Push/pull keyless release allows easy adjustments • System supports both 1.5 mm and 2 mm cables • Low-profile locking device minimizes visual impact • Cable spread of 90 degrees allows positioning the device closer to the load • Keyless release tubes are easy to operate while wearing gloves • Double-sided locking mechanism enables simple height adjustment • Individual packaging holds wire rope neatly until objects are ready to install Speed Link SLK Speed Link SLK Speed Link SLK Speed Link SLK with Shot-Fire Bracket with Hammer-On Flange Clip with Decking Hook with Angle Bracket Speed Link SLK Speed Link SLK Speed Link SLK Speed Link SLK with Toggle with Threaded Stud End with Hook with Loop Speed Link SLK Speed Link SLK Speed Link SLK with Wedge Anchor with Y-Toggle with Y-Hook nVent.com/CADDY | 10

11 Speed Link SLK with Angle Bracket Speed Link SLK System • Complete system includes wire, locking device and pre-assembled angle bracket end fitting • Ideal for attaching to concrete, steel or wood surfaces • Simple alternative to jack chain and additional hardware Material: Steel, Zinc alloy, Polypropylene Finish: Electro-galvanized Static Load Safety Factor: 5:1 Static Load Hole Size A HS Part Number F Wire Rope Length Wire Rope Diameter: 1.5 mm S L K15 L1A B 3.3’ 0.891” 0.281” 44 lb S L K15 L 2 A B 6.6’ 0.891” 0.281” 44 lb 0.891” SLK15L3AB 9.9’ 44 lb 0.281” S L K15 L5 A B 16.4’ 0.281” 44 lb 0.891” Wire Rope Diameter: 2.0 mm 6.6’ 0.891” 0.281” 100 lb SLK2L2AB SLK2L3AB 9.9’ 0.891” 0.281” 100 lb SLK2L5AB 0.891” 0.281” 100 lb 16.4’ Height Width Thickness Angle a T W H 3/4” 1/2” 90° Max 2.15” | 11 nVent.com/CADDY

12 Speed Link SLK with Shot-Fire Bracket Speed Link SLK System Complete system includes wire, locking device and shot-fire bracket with pre-assembled drive pin from Powers Fasteners, Inc. • • Quickly and easily attaches to concrete, steel or composite metal decking using gas and powder-activated tools • ICC-ES evaluation report available for drive pin from Powers Fasteners, Inc. Material: Steel, Zinc alloy, Polypropylene Finish: Electro-galvanized Static Load Safety Factor: 5:1 Static Load A B C Part Number F Wire Rope Length Wire Rope Diameter: 1.5 mm SLK15L1SF 3.3’ 1.48” 0.3” 1 1/4” 44 lb SLK15L2SF 1.48” 0.3” 1 1/4” 44 lb 6.6’ 44 lb 9.9’ 1.48” 0.3” 1 1/4” SLK15L3SF 44 lb 1 1/4” 16.4’ SLK15L5SF 0.3” 1.48” Wire Rope Diameter: 2.0 mm 6.6’ 1.48” 0.3” 1 1/4” 100 lb SLK2L2SF SLK2L3SF 9.9’ 1.48” 0.3” 1 1/4” 100 lb 0.3” SLK2L5SF 16.4’ 1.48” 1 1/4” 100 lb Height Width Thickness Angle a T W H 2.15” 3/4” 1/2” 90° Max Uses Powers Fasteners, Inc. part number 50032. For minimum fastener embedment depths in steel or concrete, please consult www.powers.com. Pre-assembled drive pin from Powers Fasteners, Inc. works with SPIT® P200, P45, P60; Ramset® TS750P, TS60P; Hilti® DX36M, DX350, DX351, DXA40; Würth Diva-1, BST-1, BST-2 or equivalent nailers. nVent.com/CADDY | 12

13 Speed Link SLK with Decking Hook Speed Link SLK System Complete system includes wire, locking device and pre-assembled decking hook end fitting • • Quickly and easily attaches to hollow metal decking • Spring-loaded ends snap into decking hole and lock into place Innovative design helps protect the wire from sharp edges of decking hole, minimizing risk of damage to wire • Material: Steel, Zinc alloy, Polypropylene Finish: Electro-galvanized Static Load Safety Factor: 5:1 Static Load Hole Size Roof Decking Sheet Thickness Wire Rope Length HS Part Number F A Wire Rope Diameter: 1.5 mm SLK15L3DH 9.9’ 16 GA Max 0.36” 0.315” 44 lb 44 lb 0.315” SLK15L5DH 16.4’ 16 GA Max 0.36” Wire Rope Diameter: 2.0 mm 9.9’ 16 GA Max 0.36” 0.315” 100 lb SLK2L3DH SLK2L5DH 16.4’ 16 GA Max 0.36” 0.315” 100 lb 16 GA Max SLK2L7DH 22.9’ 0.36” 0.315” 100 lb Height Width Thickness Angle a T W H 2.15” 3/4” 1/2” 90° Max Load rating is only applicable if the load-bearing capacity of the supporting element (steel decking) is adequate. Check with deck manufacturer for recommended load capacity. 13 | nVent.com/CADDY

14 Speed Link SLK with Hammer-On Flange Clip Speed Link SLK System Complete system includes wire, locking device and pre-assembled nVent CADDY Hammer-On Flange Clip end fitting • • Installs with just a hammer • Fits most beams and bulb tees Material: Spring Steel, Zinc alloy, Polypropylene Finish: Electro-galvanized Static Load Safety Factor: 5:1 Flange Thickness Static Load Part Number FT Wire Rope Length F Wire Rope Diameter: 1.5 mm SLK15L34H24 9.9’ 1/8” – 1/4” 44 lb 5/16” – 1/2” 44 lb SLK15L34H58 9.9’ Wire Rope Diameter: 2.0 mm 9.9’ 1/8” – 1/4” 100 lb SLK2L34H24 9.9’ SLK2L34H58 5/16” – 1/2” 100 lb Height Width Thickness Angle H T W a 2.15” 3/4” 1/2” 90° Max nVent.com/CADDY | 14

15 Speed Link SLK with Hook Speed Link SLK System • Complete system includes wire, locking device and pre-assembled hook end fitting • Hooks to a wide range of nVent CADDY fasteners Fastens to the building structure or hanging services by looping around • and hooking to wire rope • Easy to remove for applications requiring maintenance • Spring latch helps provide secure connection • Insert cable through hole and use bottom side of hook as an end stop • Also available in Y-hook configuration Material: Steel, Polypropylene, Zinc alloy Finish: Electro-galvanized Static Load Safety Factor: 5:1 Standard Static Load Packaging B A Wire Rope Length Part Number F C Quantity Wire Rope Diameter: 1.5 mm 3.3’ 2.3” 0.9” 1/4” 44 lb 20 pc S L K15 L1 6.6’ 2.3” 0.9” 1/4” 44 lb 20 pc S L K15 L 2 SLK15L2R2 6.6’ 1.89” 0.71” 0.18” 44 lb 15 x 2 pc SLK15L3 9.9’ 0.9” 1/4” 44 lb 20 pc 2.3” SLK15L3R2 1.89” 0.71” 0.18” 44 lb 15 x 2 pc 9.9’ S L K15 L5 16.4’ 2.3” 0.9” 1/4” 44 lb 20 pc SLK15L5R2 1.89” 0.71” 0.18” 44 lb 15 x 2 pc 16.4’ 20 pc 22.9’ 2.3” 0.9” 1/4” 44 lb SLK15L7 0.9” SLK15L10 32.8’ 2.3” 20 pc 1/4” 44 lb Wire Rope Diameter: 2.0 mm S L K 2 L1 0.9” 1/4” 100 lb 10 pc 3.3’ 2.3” 2.3” 0.9” 1/4” 100 lb 10 pc SLK2L2 6.6’ 6.6’ 2.24” 0.79” 0.22” 100 lb 15 x 2 pc SLK2L2R2 9.9’ 0.9” 1/4” 100 lb 10 pc 2.3” SLK2L3 9.9’ 2.24” 0.79” 0.22” 100 lb 15 x 2 pc SLK2L3R2 100 lb 16.4’ 2.3” 0.9” 1/4” 10 pc SLK2L5 SLK2L5R2 16.4’ 0.79” 0.22” 100 lb 15 x 2 pc 2.24” SLK2L7 2.3” 0.9” 1/4” 100 lb 10 pc 22.9’ SLK2L10 32.8’ 2.3” 0.9” 1/4” 100 lb 10 pc SLK2L10R2 2.24” 0.79” 0.22” 100 lb 15 x 2 pc 32.8’ Height Angle Width Thickness W T H a 2.15” 3/4” 1/2” 90° Max | 15 nVent.com/CADDY

16 Speed Link SLK with Loop Speed Link SLK System • Complete system includes wire, locking device and pre-assembled loop end fitting • Easy and flexible solution attaches to building structures • Wire rope wraps around structure and through loop for quick installation • Ideal for attaching to purlins, beams and other structural members • Works well in tight or confined spaces • Loop attaches directly to pipe, ductwork or other hanging assemblies Material: Steel, Polypropylene, Zinc alloy Finish: Electro-galvanized Static Load Safety Factor: 5:1 Length Static Load Part Number Wire Rope Length L F Wire Rope Diameter: 1.5 mm SLK15L1LP 3.3’ 4” 44 lb SLK15L1LPR2 4” 44 lb 3.3’ SLK15L2LP 6.6’ 4” 44 lb SLK15L2LPR2 6.6’ 4” 44 lb SLK15L3LP 9.9’ 4” 44 lb SLK15L3LPR2 9.9’ 4” 44 lb 44 lb 4” SLK15L5LP 16.4’ SLK15L5LPR2 4” 44 lb 16.4’ SLK15L7LP 22.9’ 4” 44 lb SLK15L10LP 32.8’ 4” 44 lb Wire Rope Diameter: 2.0 mm SLK2L1LP 3.3’ 4” 100 lb SLK2L2LP 6.6’ 4” 100 lb 4” SLK2L3LP 9.9’ 100 lb SLK2L5LP 16.4’ 100 lb 4” 22.9’ 4” SLK2L7LP 100 lb SLK2L10LP 32.8’ 4” 100 lb Height Angle Width Thickness W T H a 2.15” 3/4” 1/2” 90° Max nVent.com/CADDY | 16

17 Speed Link SLK with Threaded Stud End Speed Link SLK System • Complete system includes wire, locking device and pre-assembled threaded stud end fitting • Attaches to structures with threaded anchors or devices with threaded hole • Connects directly to threaded devices in trapeze assemblies, light fixtures, HVAC assemblies or signage Material: Steel, Polypropylene, Zinc alloy Finish: Electro-galvanized Static Load Safety Factor: 5:1 Static Load Screw Length Rod Size RS L Part Number F Wire Rope Length Wire Rope Diameter: 1.5 mm SLK15L2SE250 3.3’ 1/4” 1” 44 lb SLK15L3SE250 9.9’ 1/4” 1” 44 lb 1/4” SLK15L5SE250 16.4’ 44 lb 1” Wire Rope Diameter: 2.0 mm SLK2L2SE250 1/4” 1” 100 lb 6.6’ 9.9’ 1/4” 1” 100 lb SLK2L3SE250 SLK2L5SE250 16.4’ 1/4” 1” 100 lb Angle Height Width Thickness W T H a 2.15” 3/4” 1/2” 90° Max | 17 nVent.com/CADDY

18 Speed Link SLK with Toggle Speed Link SLK System Complete system includes wire, locking device and pre-assembled toggle end fitting • • Attaches to clearance holes in a variety of structures or hanging devices • Ideal for supporting lighting fixtures • Also available in Y-toggle configuration Material: Steel, Zinc alloy, Polypropylene Finish: Electro-galvanized Static Load Safety Factor: 5:1 Wire Rope Diameter: 1.5 mm Static Load Wire Rope Length B Part Number F A S L K15 L1T 3.3’ 1 1/2” 0.2” 44 lb SLK15L1TR2 3.3’ 1 1/2” 0.2” 44 lb S L K15 L 2T 6.6’ 1 1/2” 0.2” 44 lb 44 lb 0.2” SLK15L2TR2 6.6’ 1 1/2” SLK15L3T 1 1/2” 0.2” 44 lb 9.9’ SLK15L3TR2 9.9’ 1 1/2” 0.2” 44 lb S L K15 L5 T 16.4’ 1 1/2” 0.2” 44 lb 1 1/2” SLK15L7T 22.9’ 0.2” 44 lb SLK15L10T 1 1/2” 0.2” 44 lb 32.8’ Height Width Thickness Angle W T H a 2.15” 3/4” 1/2” 90° Max nVent.com/CADDY | 18

19 Speed Link SLK with Y-Hook Speed Link SLK System Complete system includes wire, locking device and two pre-assembled hook end fittings • • Fastens to the building structure and hooks to hanging services and tray • Spring latch helps provide secure connection • Convenient design allows one hook to be temporarily detached for maintenance or to add cables to the tray • Single drop with double hook provides increased stability to the system Also available in a single-hook end fitting configuration • Material: Steel, Zinc alloy, Polypropylene Finish: Electro-galvanized Static Load Safety Factor: 5:1 Wire Rope Diameter: 2 mm Wire Rope”Y” Length Static Load Wire Rope Length Part Number A C YL F B SLK2YH500L2 100 lb 19.6” 2.3” 0.9” 1/4” 6.6’ 1/4” SLK2YH500L2R2 6.6’ 19.6” 2.3” 0.9” 100 lb SLK2YH500L3 2.3” 0.9” 1/4” 100 lb 19.6” 9.9’ 9.9’ 19.6” 2.3” 0.9” 1/4” 100 lb SLK2YH500L3R2 19.6” 22.3’ 2.3” SLK2YH500L7 0.9” 1/4” 100 lb Angle Height Width Thickness W T H a 2.15” 3/4” 1/2” 90° Max | 19 nVent.com/CADDY

20 Speed Link SLK with Y-Toggle Speed Link SLK System Complete system includes wire, locking device and two pre-assembled toggle end fittings • • Attaches to clearance holes in a variety of structures or hanging devices • Ideal for supporting lighting fixtures Material: Steel, Zinc alloy, Polypropylene Finish: Electro-galvanized Static Load Safety Factor: 5:1 Wire Rope “Y” Length Static Load Part Number Wire Rope Length B YL F A Wire Rope Diameter: 1.5 mm SLK15Y300L3 9.9’ 11.8” 1.65” 0.31” 44 lb SLK15Y300L3R2 9.9’ 11.8” 1.50” 0.20” 44 lb SLK15Y500L3 19.6” 1.65” 0.31” 44 lb 9.9’ SLK15Y500L3R2 9.9’ 19.6” 1.50” 0.20” 44 lb SLK15Y300L5 16.4’ 11.8” 1.65” 0.31” 44 lb Wire Rope Diameter: 2.0 mm 11.8” 100 lb SLK2Y300L2 6.6’ 0.31” 1.65” SLK2Y300L3 9.9’ 1.65” 0.31” 100 lb 11.8” SLK2Y300L3R2 11.8” 1.65” 0.31” 100 lb 9.9’ SLK2Y500L3 9.9’ 19.6” 1.65” 0.31” 100 lb SLK2Y300L5 16.4’ 11.8” 1.65” 0.31” 100 lb SLK2Y300L7 22.9’ 11.8” 1.65” 0.31” 100 lb SLK2Y300L10 11.8” 1.65” 0.31” 100 lb 32.8’ Height Width Thickness Angle W T H a 2.15” 3/4” 1/2” 90° Max nVent.com/CADDY | 20

21 Speed Link SLK with Wedge Anchor Speed Link SLK System Complete system includes wire, locking device and wedge anchor from Powers Fasteners, Inc. • • Quickly and easily attaches into cracked and non-cracked concrete • No special tools required W L H T a F W Material: Steel; Polypropylene; Zinc Alloy Finish: Electrogalvanized Static Load Safety Factor: 5:1 Drill Bit Diameter: 1/4” Drill Bit Depth: 2.4” Static Load Height Width Thickness Wire Rope Angle Length Length W Part Number L T a H F Wire Rope Diameter: 2 mm 6.6' 2.50” 2 .15 " 0.75" 0.5" 90° Max 100 lb SLK2L2WA6 SLK2L3WA6 9.9' 2.50” 2 .15 " 0.75" 0.5" 90° Max 100 lb SLK2L5WA6 16.4' 2.50” 2 .15 " 0.75" 0.5" 90° Max 100 lb SLK2L7WA6 100 lb 22.9' 2.50” 2 .15 " 0.75" 0.5" 90° Max Wire Rope Diameter: 3 mm 2.50” 2.50" 0.90" 0.6" 90° Max 200 lb 3.3' S L K 3 L1WA 6 6.6' 2.50” 2.50" 0.90" 0.6" 90° Max 200 lb SLK3L2WA6 9.9' 2.50” 2.50" 0.90" 0.6" 90° Max 200 lb SLK3L3WA6 SLK3L5WA6 16.4' 2.50” 2.50" 0.90" 0.6" 90° Max 200 lb SLK3L7WA6 2.50” 2.50" 0.90" 0.6" 90° Max 200 lb 22.9' SLK3L10WA6 32.8' 2.50” 2.50" 0.90" 0.6" 90° Max 200 lb Uses Powers Fasteners, Inc. part number 7409SD1. For minimum fastener embedment depths in concrete, please consult www.powers.com. | 21 nVent.com/CADDY

22 Speed Link LD System The Speed Link LD system is ideal for hanging light-duty fixtures, ductwork, speakers, alarm sensors, signage and pipes in applications that require all stainless steel components for a greater corrosion resistance. Systems include locking device, 1.5 mm diameter wire rope, and specialty end fitting • • Low-profile locking device minimizes visual impact • Individual packaging holds wire rope neatly until objects are ready to install • Supported objects are easy to adjust both during and after installation Speed Link LD with Hook Speed Link LD System • Complete system includes wire, locking device and pre-assembled hook end fitting • Hooks to a wide range of nVent CADDY fasteners • Fastens to the building structure or hanging services by looping around and hooking to wire rope • Easy to remove for applications requiring maintenance • Spring latch helps provide secure connection • Insert cable through hole and use bottom side of hook as an end stop Material: Stainless steel 304 Static Load Safety Factor: 5:1 Standard Wire Rope Wire Rope Static Load Packaging Diameter A B C Quantity F Length Part Number S L D15 L 2S 2.3” 0.9” 1/4” 44 lb 20 x 2 pc 1.5 mm 6.6’ 20 x 2 pc 1.5 mm 2.3” 0.9” 1/4” 44 lb S L D15 L5 S 16.4’ SLD15L10S 32.8’ 1.5 mm 2.3” 0.9” 1/4” 44 lb 20 x 2 pc Height Width H W 3/4” 1/2” nVent.com/CADDY | 22

23 Speed Link SLS Device AESTHETICAL FEATURES EASE OF USE FEATURES SAFETY FEATURES Low-profile locking device “Push-to-install” retaining nut Length of stem allows the device simplifies installation to be installed in strut profiles provides a positive aesthetic without the need to insert fingers to a finished project or too ls into the strut Engineered elongated retaining nut reduces unwanted sway of the trapeze during installation UL Listing on all 4 end fittings for and provides higher stability pre-cut lengths Two jaws grip the wire inside the device, holding the wire The outside of the housing is more securely than single-cam threaded for easy and secure devices common among most attachment to the nut competitors Speed Link is lighter, faster to install, easier to transport Speed Link SLS System and generates less waste than Keyless release tube is alternative hanging methods designed to allow safe and easy adjustment, even while wearing bulky gloves Two tool-free locking devices are available for three wire sizes: • SLS2 compatible with 1.5mm and 2mm wire • SLS3 compatible with 3mm wire The color of the line corresponds to the larger goal of each feature: SAFETY FEATURES AESTHETICAL FEATURES EASE OF USE FEATURES Similar housing style creates a consistent look when used in projects alongside the Speed Link SLK System | 23 nVent.com/CADDY

24 Speed Link SLS System The Speed Link SLS system is an innovative cable solution for supporting metal framing channels, ceiling fan units, and other hangers. The locking device is similar to the keyless design of Speed Link SLK but with a single barrel. The outside of the housing is threaded and is held in a channel or hanger by a push-to-install retaining nut. This engineered elongated retaining nut reduces unwanted sway of the trapeze during installation and provides higher stability. The system allows for quick and easy prefabrication of complex assemblies at ground level that can be easily lifted and held in place by wire rope. • Single barrel locking device allows for quick prefabrication of strut or brackets • Push-on nut quickly and securely installs to strut or bracket to keep the locking device in position and eases installation • Finger tightening of nut secures the locking device into position without tools Installs in strut profiles without the need to insert fingers or tools into the strut • • Push-on nut guides the cable into the locking device and brings stability to the support • Installs with open side of the strut channel facing up or down for mor e flexibility Speed Link SLS Speed Link SLS Speed Link SLS Speed Link SLS with Decking Hook with Threaded Stud End with Hook with Wedge Anchor nVent.com/CADDY | 24

25 Speed Link SLS with Decking Hook Complete system includes wire, locking device and pre-assembled decking hook end fitting • • Quickly and easily attaches to hollow metal decking • Spring-loaded ends snap into decking hole and lock into place • Innovative design helps protect the wire from sharp edges of decking hole, minimizing risk of damage to wire A HS1 H1 HS2 W SS TS T H2 F Speed Link SLS System Material: Steel; Polypropylene; Zinc Alloy Finish: Electrogalvanized Static Load Safety Factor: 5:1 Wire Rope Diameter: 2 mm Wire Rope Roof Decking Sheet Hole Size 1 Static Load Thickness A Part Number HS1 F Length 0.315” SLS2L3DH 9.9' 16 GA Max 0.36” 60 lb SLS2L5DH 0.315” 60 lb 0.36” 16 GA Max 16.4' 0.315” 0.36” SLS2L7DH 60 lb 22.9' 16 GA Max Height 1 Height 2 Width Thread Size Thickness Hole Size 2 Slot Size H1 TS T H2 HS2 W SS 0.31" – 0.38" M8 1.8" 0.6" 0.15" Max 2 .1" 0.31" x 0.25" - 0.31" x 0.38" The 2 mm locking device is compatible with C-Channel Types E0 and E0L. Total load per wire on a multi-tier trapeze must not exceed static load. Load rating is only applicable if the load-bearing capacity of the supporting element (steel decking) is adequate. Check with deck manufacturer for recommended load capacity. | 25 nVent.com/CADDY

26 Speed Link SLS with Hook Complete system includes wire, locking device and pre-assembled hook end fitting • • Hooks to a wide range of nVent CADDY fasteners • Fastens to the building structure or hanging services by looping around and hooking to wire rope • Easy to remove for applications requiring maintenance Speed Link SLS System • Spring latch helps provide secure connection • Insert cable through hole and use bottom side of hook as an end stop B C H1 A HS W SS TS H2 T F Material: Steel; Polypropylene; Zinc Alloy Finish: Electrogalvanized Static Load Safety Factor: 5:1 Wire Rope Diameter: 2 mm Part Number SLS2L1 SLS2L2 SLS2L3 SLS2L5 SLS2L7 SLS2L10 Wire Rope Length 3.3' 6.6' 9.9' 16.4' 22.9' 32.8' A 2.24" B 0.79" C 0.22" ( ) H1 2 .1" Height 1 ( ) H2 1.7" Height 2 ( ) TS M8 Thread Size ( ) W Width 0.63" ( ) HS Hole Size 0.31" – 0.38" ) ( Slot Size SS 0.31" x 0.25" - 0.31" x 0.38" ) ( T Thickness 0.15" Max ( ) Static Load F 60 lb Standard Packaging Quantity 10 pc nVent.com/CADDY | 26

27 Wire Rope Diameter: 3 mm Part Number SLS3L2 SLS3L3 SLS3L5 SLS3L7 SLS3L10 SLS3L1 3.3' 6.6' 9.9' 16.4' 22.9' 32.8' Wire Rope Length A 2.27" B 0.91" C 0.24" ) ( H1 Height 1 2 .1" ( ) Height 2 H2 1.8" ( ) Thread Size M12 TS ) ( Width 0.80" W ( ) HS 0.50" – 0.56" Hole Size ( ) SS 0.47" x 0.39" - 0.47" x 0.56" Slot Size ( ) Thickness T 0.25" Max ( ) Static Load F 150 lb 5 x 5 pc Standard Packaging Quantity 10 x 10 pc 10 x 5 pc The 2 mm locking device is compatible with C-Channel Types E0 and E0L. The 3 mm locking device is compatible with C-Channel Types E1, E2, E2L, E3, E4, E5, Strut Channel Type C, Slotted, Strut Channel Type A, Slotted, Strut Channel Type AS, Perforated, Strut Channel Type CC, Slotted, Strut Channel Type AA, Slotted. Total load per wire on a multi-tier trapeze must not exceed static load. Speed Link SLS System | 27 nVent.com/CADDY

28 Speed Link SLS with Threaded Stud End Complete system includes wire, locking device and pre-assembled threaded stud end fitting • • Attaches to structures with threaded anchors or devices with threaded hole RS Speed Link SLS System L H1 HS2 W SS TS H2 T F Material: Steel; Polypropylene; Zinc Alloy Finish: Electrogalvanized Static Load Safety Factor: 5:1 Wire Rope Diameter: 2 mm Wire Rope Rod Size Screw Length Static Load RS Length L F Part Number 60 lb 1" SLS2L2SE250 6.6' 1/4" 1/4" 1" 60 lb 9.9' SLS2L3SE250 1" SLS2L5SE250 16.4' 1/4" 60 lb Thread Size Height 1 Height 2 Width Thickness Hole Size 2 Slot Size W H1 T TS HS2 H2 SS M8 2 .1" 1.7" 0.63" 0.15" Max 0.31" – 0.38" 0.31" x 0.25" - 0.31" x 0.38" The 2 mm locking device is compatible with C-Channel Types E0 and E0L. Total load per wire on a multi-tier trapeze must not exceed static load. nVent.com/CADDY | 28

29 Speed Link SLS with Wedge Anchor Complete system includes wire, locking device and wedge anchor from Powers Fasteners, Inc. • • Quickly and easily attaches into cracked and non-cracked concrete • No special tools required • ETA-13/0106 approval available for wedge anchor from Powers Fasteners, Inc L H1 HS W SS TS H2 T Speed Link SLS System F Material: Steel; Polypropylene; Zinc Alloy Finish: Electrogalvanized Static Load Safety Factor: 5:1 Wire Rope Diameter: 2 mm Static Load Wire Rope Length Drill Hole Drill Bit Diameter ) ( L Ø Length Depth Part Number F 2.50” SLS2L3WA6 9.9' 60 lb 1/4” 2.4” SLS2L5WA6 2.4” 60 lb 1/4” 2.50” 16.4' 2.4” 1/4” SLS2L7WA6 60 lb 22.9' 2.50” Height 1 Height 2 Width Thread Size Thickness Hole Size Slot Size H1 TS T H2 HS W SS 0.31" – 0.38" M8 1.7" 0.63" 0.15" Max 2 .1" 0.31" x 0.25" - 0.31" x 0.38" The 2 mm locking device is compatible with C-Channel Types E0 and E0L. Total load per wire on a multi-tier trapeze must not exceed static load. For minimum fastener embedment depths in concrete, please consult www.powers.com. Uses Powers Fasteners, Inc. part number 7409SD1. | 29 nVent.com/CADDY

30 Speed Link Extensions Speed Link extensions allow standard Speed Link Systems to be lengthened for long drop applications, putting the height adjustment closer to the object being supported. These short sections of wire include speciality end fittings at one end and a small loop or hook at the other. The extensions combine perfectly with other Speed Link Systems, and can also be used separately as a backup wire. • Ideal for use with standard Speed Link Systems A range of end fittings easily adapt to various jobs • • Wire rope is securely looped and crimped • Ideal as a support or secondary wire Speed Link Y-Toggle with Speed Link Y-Hook with Eyelet Speed Link Y-Toggle with Hook Speed Link Quad-Toggle with Eyelet Extension Extension Extension Eyelet Extension Speed Link Extensions | nVent.com/CADDY 30

31 Speed Link Y-Hook with Eyelet Extension • Double hook offers easy attachment to basket tray, cable tray or lighting • Convenient design allows one hook to be temporarily detached for maintenance or to add cables to the tray • Y-design provides improved stability • Spring latch helps provide secure connection Material: Steel Finish: Electro-galvanized Static Load Safety Factor: 5:1 Wire Rope “Y” Length Static Load YL A B C Part Number F Wire Rope Diameter: 2 mm 19.6” SLD2YH500 2.3” 100 lb 1/4” 0.9” Speed Link Exiensions SLD2YH800 31.4” 2.3” 0.9” 1/4” 100 lb Wire Rope Diameter: 3 mm SLD3YH500 19.6” 200 lb 1/4” 0.9” 2.3” SLD3YH800 31.4” 2.3” 0.9” 1/4” 200 lb Speed Link locking device not included. The 2 mm locking device is compatible with C-Channel Types E0 and E0L. The 3 mm locking device is compatible with C-Channel Types E1, E2, E2L, E3, E4, E5, Strut Channel Type C, Slotted, Strut Channel Type A, Slotted, Strut Channel Type AS, Perforated, Strut Channel Type CC, Slotted, Strut Channel Type AA, Slotted. Total load per wire on a multi-tier trapeze must not exceed static load. 31 | nVent.com/CADDY

32 Speed Link Y-Toggle with Eyelet Extension • Attaches to clearance holes in a variety of structures or hanging devices • Ideal for supporting lighting fixtures • Y-design provides improved stability Material: Steel Finish: Electro-galvanized Static Load Safety Factor: 5:1 Standard Wire Rope “Y” Length Static Load A YL F Part Number Packaging Quantity B Wire Rope Diameter: 1.5 mm SLD15Y200 7.8” 1.65” 0.31” 44 lb 20 pc SLD15Y300 11.8” 1.65” 0.31” 44 lb 20 pc 44 lb 0.31” 20 pc SLD15Y500 19.6” 1.65” SLD15Y500TP 1.65” 0.31” 44 lb 20 x 2 pc 19.6” SLD15Y800 31.4” 1.65” 0.31” 44 lb 20 pc 44 lb SLD15Y800TP 31.4” 1.65” 0.31” 20 x 2 pc Speed Link Extensions Wire Rope Diameter: 2.0 mm 11.8” 0.31” 100 lb 20 pc SLD2Y300 1.65” SLD2Y500 1.65” 0.31” 100 lb 20 pc 19.6” Speed Link locking device not included. nVent.com/CADDY | 32

33 Speed Link Y-Toggle with Hook Extension • Attaches to clearance holes in a variety of structures or hanging devices • Ideal for supporting lighting fixtures • Y-design provides improved stability • Spring latch of hook helps provide secure connection • Hooks to a wide range of CADDY fasteners Material: Steel Finish: Electro-galvanized Static Load Safety Factor: 5:1 Wire Rope”Y” Wire Rope Length Static Load Wire Rope Part Number Diameter Length A B C D E YL F 11.8” SLD2Y300L050H 2 mm 0.31” 2.0” 2.3” 0.9” 1/4” 1.65” 100 lb Speed Link locking device not included. Speed Link Quad-Toggle with Eyelet Extension Speed Link Extensions • Secure hanging solution for use on control access points, projectors, etc. Material: Steel Finish: Electro-galvanized Static Load Safety Factor: 5:1 Static Load Wire Rope “Y” Length YL F B Wire Rope Diameter Part Number A SLD15QT250 9.8” 1.65” 0.31” 44 lb 1.5 mm Speed Link locking device not included. | 33 nVent.com/CADDY

34 Speed Link Locking Devices and Wire Rope The individual components of the Speed Link Universal Support System can be configured to meet installers’ unique needs. Speed Link locking devices and wire rope are available in bulk and allow installers to customize the system for each project. Wire Spool Wire Rope Cutter Speed Link SLK Locking Speed Link SLK Spool Kit Device Speed Link LD Locking Speed Link SLS Locking Speed Link SLK Spool KIt Device Device nVent.com/CADDY | 34

35 Speed Link SLK Spool Kit • Kit includes spool of Speed Link steel wire and Speed Link SLK locking devices • Wire spool and locking devices are packaged together, simplifying transportation to the jobsite and reducing inventory • Packaging allows end-users to pull and cut any length of wire that is needed without having to take the spool out of the box • Ideal for rework and installations where custom lengths of wire may be needed • Wire rope constructed from seven bundles of seven strands each of steel aircraft wire • Push/pull keyless release allows easy adjustments • Low-profile locking device minimizes visual impact Cable spread of 90 degrees allows positioning the device closer to the load • • Keyless release tubes are easy to operate while wearing gloves • Double-sided locking mechanism enables simple height adjustment Material: Steel Finish: Electrogalvanized Part Number Wire Rope Diameter Length Number of Locking Devices SLK15L50MPACK 1.5 mm 16 4’ 25 2.0 mm 50 328’ SLK2L100PACK Wire Spool • Spool with Speed Link steel wire • Wire rope constructed from seven bundles of seven strands each of steel aircraft wire Material: Steel Speed Link SLK Spool KIt Finish: Electro-galvanized Part Number Wire Rope Diameter Length Static Load SLC15L50MSP 1.5 mm 16 4’ 44 lb SLC15L1000SP 1.5 mm 1,000’ 44 lb SLC2L1000SP 2.0 mm 1,000’ 100 lb 200 lb 1,000’ 3.0 mm SLC3L1000SP Wire Rope Cutter • Designed to reduce wire rope fraying Material: Steel Part Number SLWC | 35 nVent.com/CADDY

36 Speed Link SLK Locking Device • Push/pull keyless release allows easy adjustments • Suitable for 1.5 mm and 2 mm Speed Link cable • Low-profile locking device minimizes visual impact • Cable spread of 90 degrees allows positioning the device closer to the load • Keyless release tubes are easy to operate while wearing gloves • Double-sided locking mechanism enables simple height adjustment Material: Steel, Polypropylene, Zinc alloy Height Width Thickness Angle a Wire Rope Diameter H W T Part Number SLK2C200 2.15” 0.75” 1.5 – 2.0 mm 0.5” 90° Max SLK2C50 2.15” 0.75” 0.5” 90° Max 1.5 – 2.0 mm 3.0 mm 0.6” 0.90” SLK3C200 90° Max 2.50” 3.0 mm SLK3C50 0.90” 0.6” 90° Max 2.50” Locking device is only to be used with SLC15L50MSP, SLC15L1000SP and SLC2L1000SP wire spools or 1.5 mm and 2 mm Speed Link accessories. Do not use with any other wires. Speed Link SLK Spool KIt Speed Link LD Locking Device • Low-profile locking device minimizes visual impact • Suitable for 1.5 mm Speed Link cable Material: Stainless steel 304 Height Width Part Number Wire Rope Diameter H W 0.75” SLJR200 0.5” 1.5 mm SLS2C50 2 mm 2.1” 0.63” 0.80” SLS3C50 3 mm 2.1” The 1.5 mm locking devices are only to be used with the SLC15L1000SP and SLC15L50MSP wire spools, or any other 1.5 mm Speed Link accessories. Do not use with any other wires. nVent.com/CADDY | 36

37 Speed Link SLS Locking Device • Single barrel locking device allows for quick prefabrication of strut or brackets • Push-on nut quickly and securely installs to strut or bracket to keep the locking device in position and eases installation • Finger tightening of nut secures the locking device into position without tools • Installs in strut profiles without the need to insert fingers or tools into the strut • Push-on nut guides the cable into the locking device and brings stability to the support • Installs with open side of the strut channel facing up or down for mor e flexibility Material: Steel, Polypropylene, Zinc Alloy Thickness Hole Size Wire Rope Slot Size Thread Size Width Height 1 Height 2 H1 TS W Diameter T Part Number HS SS H2 0.31” x 0.25” SLS2C50 2.0 mm M8 2.1” 1.7” 0.63” 0.15” Max 0.31” – 0.38” - 0.31” x 0.38” 0.47” x 0.39” SLS3C50 3.0 mm M12 2.1” 1.8” 0.80” 0.25” Max 0.50” – 0.56” Speed Link SLK Spool KIt - 0.47” x 0.56” The 2 mm locking device is compatible with C-Channel Types E0 and E0L. The 3 mm locking device is compatible with C-Channel Types E1, E2, E2L, E3, E4, E5, Strut Channel Type C, Slotted, Strut Channel Type A, Slotted, Strut Channel Type AS, Perforated, Strut Channel Type CC, Slotted, Strut Channel Type AA, Slotted. Locking devices are only to be used with Speed Link wire spools and accessories with the same specified Wire Rope Diameter as the locking device. Do not use with any other wires. | 37 nVent.com/CADDY

38 Speed Link Accessories Speed Link accessories are specially designed to work with Speed Link systems. Locking devices and bulk wire are available for highly customized applications. Other accessories complement the Speed Link portfolio to simplify installation. Concrete Fixing Eyebolt Air Duct Support Air Duct Corner Protector Eye Screw Screw Attachment Angle Bracket With MC/AC Cable Clip Light Duty Light Oblong Hole Fixture Eyelet The nVent CADDY catalog also has many structural attachments to adapt Speed Link end fittings to most typical structural types. Visit nVent.com/CADDY to view the full nVent CADDY catalog and be sure to contact us if you have questions about a unique configuration. Speed Link Accessories | nVent.com/CADDY 38

39 Air Duct Corner Protector • Includes rib to keep the wire rope in place • Prevents the wire rope from damaging the duct Material: Polyvinylchloride Color: Black Part Number A B C SLADCP 2” 2” 1/2” Air Duct Support Attachment • Angled bracket for installation on to round or square duct • Designed to accept Speed Link wire rope or hook Material: Steel Finish: Electro-galvanized Thickness Hole Size 2 Hole Size 1 Part Number HS2 A B HS1 T SLADS 0.314” 0.165” 0.787” 0.393” 0.059” Speed Link Accessories | 39 nVent.com/CADDY

40 Concrete Fixing Eyebolt Screw • • For use in concrete and brick • Includes drill bit adaptor for easy installation Material: Steel Finish: Electro-galvanized Screw Diameter Hole Size Screw Length Static Load Part Number Sc HS L A Drill Bit Size F 0.197” 15 5 lb CFEB05 0.256” H6 1.77” 2.36” Eye Screw Material: Steel Finish: Electro-galvanized Screw Diameter Screw Length Hole Size Length Sc L HS L Part Number 0.984” SLEB250 1/4” 0.283” 1.732” SLEBWS 2.360” 0.345” 2.375” H6 SLEB375 3/8” 1.8” 0.283” 2 1/2” Speed Link Accessories nVent.com/CADDY | 40

41 MC/AC Cable Clip • Spring steel cable attachment • Allows for electrical cable to be attached to Speed Link wire rope Material: Spring Steel Finish: nVent CADDY Armour Outer Diameter Part Number Wire Rope Diameter OD S L1214 0.468” – 0.562” 1.5 – 3.0 mm SL1518 0.500” – 0.718” 1.5 – 3.0 mm Light Duty Light Fixture Eyelet Inserts into openings of light fixture • • Hook or loop through lighting clip to suspend lighting from wire rope or chain Material: Stainless steel 302 Static Load Diameter A Ø Part Number F 0.052” 12 lb SLLC250 5/16” Do not use light fixture eyelet as a lifting device. Speed Link Accessories | 41 nVent.com/CADDY

42 Multiply the time savings and flexibility with Telescoping Strut Replacement (TSR1220N) Like strut, the Speed Link SLS3 locking device can be inserted directly into the holes at the end of the TSR1220N. Unlike strut, Telescoping Strut Replacement products* are simply extended to any length between 12 and 20 inches, and locked in place by snapping closed a spring steel retainer clip. In addition to the quick installation of Speed Link, the TSR1220N eliminates the need to transport, measure, cut, and deburr strut. The telescoping feature also allows for quick on-site adjustments. *The Speed Link SLS3 locking device is only compatible with the TSR1220N. Visit nVent.com/ERICO to see other Telescoping Strut Replacement installations. nVent.com/CADDY | 42

43 Save Time on Heavy Duty Installations with nVent CADDY Rod Lock Want to reap the time-saving benefits of Speed Link but require a higher load rating? CADDY ROD LOCK is the solution for quick threaded rod installations. The unique “push-to-install” mechanism allows for the prefabrication of complex assemblies on the ground or off-site that can easily be lifted and locked into place. Installers no longer need to spend hours spinning hardware up threaded rod. Build. Lift. Done. Rod Lock technology is available on structural attachments as well as supports. Whatever the threaded rod application, Rod Lock products can help installers save time and money on the job site. Go to nVent.com/CADDY to learn more about Rod Lock and how it can help you save time on your next project. | 43 nVent.com/CADDY

44 Our powerful portfolio of brands: CADDY ERICO HOFFMAN RAYCHEM SCHROFF TRACER nVent.com/CADDY ©2018 nVent. All nVent marks and logos are owned or licensed by nVent Services GmbH or its affiliates. All other trademarks are the property of their respective owners. nVent reserves the right to change specifications without notice. CADDY-SB-FM1161B-DFM489LT17NA-EN-1805

Related documents