SMC Pneumatics AM/AFF Compressed Air Cleaning Filter Series

Transcript

1 176-AMG.qxd 10.5.7 10:49 AM Page 1 Compressed Air Cleaning Filter Series /  AM Series AFF For Water, Solid/Oil Separation and Deodorization HAA   C, AFF C, AMD  C, AM  C AMG HAW Modular connection, Space-saving design, Labor-saving in piping! AMH  C, AME C, AMF  C  AT Uses the same spacer as the F.R.L. combination AC series. Modular connection example IDF Possible to make a modular connection with products such as AR series regulator. IDU IDFA Note) Spacer IDFB ID AMH + AME IDG AMG AFF AM AMH + AME + AMF Note) Spacer with bracket cannot be mounted. AMD The C type is only suitable for modular connection. ∗ Use the attached bracket. AMH  C  C, AFF  C, AM  C, AMD AMG ) ( AME Options added Compact, Lightweight C  C, AMF  AME  C, AMF  C, AME AMH C  Differential pressure switch AMF % Height and mass reduced by up to 40 Addition: types 5 Conventional SF 1.6 MPa specifications New Fluororubber specifications SFD With differential pressure LLB ( ) switch 125 VAC, 30 VDC With differential pressure  AD ) ( switch 30 VDC GD Degreasing wash, white vaseline specifications Water Separation Water Separator/ AMG Solid/Oil Separation Main Line Filter/ AFF AM Mist Separator/ Micro Mist Separator/ AMD AMH Micro Mist Separator with Pre-filter/ AME Super Mist Separator/ Deodorization AMF Odor Removal Filter/ 141 CA Courtesy Engineering, Inc.-230 Ryan Way, South San Francisco, of Steven 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com

2 176-AMG.qxd 10.5.7 10:49 AM Page 2 Flow capacity Water droplet removal Water droplet removal /min (ANR) l Max. flow Note Model rt size Po Water Separator capacity at 0.7 MPa Water droplet inlet pressure separation rate: 99% 1/8, 1/4 300 150C 1/4, 3/8 750 250C 3/8, 1/2 1,500 350C Piping support 1/2, 3/4 2,200 AMG 450C type 3/4, 1 3,700 550C 1 / 1, 1 6,000 650 2 AMG150C to 550C AMG650/850 1 / 1 , 2 12,000 850 2 1/8, 1/4 300 2C Large dust particle filtration, Oil droplet separation Large dust particle filtration, Oil droplet separation 1/4, 3/8 750 4C 3/8, 1/2 1,500 8C Main Line Filter Piping support 1/2, 3/4 2,200 11C m Nominal filtration rating: 3 μ type [Filtration efficiency: 3/4, 1 3,700 22C 99%] 1 / 1, 1 6,000 AFF 37B 2 1 / 1 , 2 75B 2 12,000 50(2B) flange 75A Free 80(3B) flange 22,000 125A standing 28,000 150A type 100(4B) flange 42,000 220A AFF37B/75B AFF75A to 220A AFF2C to 22C 1/8, 1/4 300 150C Dust filtration, Oil mist separation Dust filtration, Oil mist separation Dust filtration, Oil mist separation 1/4, 3/8 750 250C 3/8, 1/2 1,500 350C Mist Separator Piping support 1/2, 3/4 2,200 450C m μ Nominal filtration rating: 0.3 AM [Filtration efficiency: 99.9%] type 3/4, 1 3,700 550C Oil mist density at outlet: 3 Max. 1.0 mg/m (ANR) 1 / 1, 1 6,000 650 2 0.8 ppm] [ ≈ 1 / 1 , 2 12,000 850 2 AM150C to 550C AM650/850 1/8, 1/4 200 150C Dust filtration, Oil mist separation Dust filtration, Oil mist separation Dust filtration, Oil mist separation 1/4, 3/8 500 250C 3/8, 1/2 1,000 350C Micro Mist Separator 1/2, 3/4 2,000 450C μ m Nominal filtration rating: 0.01 Piping [Filtration efficiency: 99.9%] support 3/4, 1 3,700 550C Oil mist density at outlet: type 3 Max. 0.1 mg/m (ANR) 1 / 1, 1 6,000 650 2 [ ≈ 0.08 ppm] AMD 1 / 1 , 2 12,000 850 2 50(2B) flange 8,000 801 24,000 50(2B), 80(3B), 100(4B) flange 901 8,000 50(2B) flange 800 Free standing 24,000 50(2B), 80(3B), 100(4B) flange 900 type 40,000 100(4B), 150(6B) flange 1000 AMD150C to 550C AMD650, 850 142 Courtesy 258-9200-www.stevenengineering.com Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) of Steven

3 176-AMG.qxd 10.5.7 10:49 AM Page 3 /AFF  AM Series Flow capacity Dust filtration, Oil mist separation Dust filtration, Oil mist separation Dust filtration, Oil mist separation l /min (ANR) Max. flow Note rt size Po Model Micro Mist Separator capacity at 0.7 MPa with Pre-filter inlet pressure m pre-filter μ Built-in 0.3 The AM + AMD element have been integrated to 200 1/8, 1/4 150C achieve a space-saving design. HAA m Nominal filtration rating: 0.01 μ HAW 500 1/4, 3/8 250C [Filtration efficiency: 99.9%] Oil mist density at outlet: AT 3 Max. 0.1 mg/m (ANR) 1,000 3/8, 1/2 350C IDF [ 0.08 ppm] ≈ Piping IDU 2,000 1/2, 3/4 450C AMH support type IDFA 3,700 3/4, 1 550C IDFB 1 / 6,000 1, 1 650 2 ID 1 / 12,000 , 2 1 850 2 AMH150C to 550C AMH650/850 IDG 200 1/8, 1/4 150C AMG Dust filtration, Oil mist adsorption Dust filtration, Oil mist adsorption Dust filtration, Oil mist adsorption 500 1/4, 3/8 250C AFF Super Mist Separator Color change indicates when element is saturated. 1,000 3/8, 1/2 350C AM m μ Nominal filtration rating: 0.01 Piping [Filtration efficiency: 99.9%] AMD 2,000 support 1/2, 3/4 450C AME Oil mist density at outlet: type 3 Max. 0.01 mg/m (ANR) AMH 3,700 3/4, 1 550C [ ≈ 0.008 ppm] Cleanliness at outlet: AME Not more than 35 1 / 6,000 1, 1 650 2 particles of size 0.3 m or larger/10 l μ AMF 1 / 3 12,000 1 , 2 850 2 (100 particles or less/ft ) AME650/850 AME150C to 550C SF 200 1/8, 1/4 150C Deodorization Deodorization SFD 500 1/4, 3/8 250C Odor Removal Filter LLB m Nominal filtration rating: 0.01 μ 1,000 350C 3/8, 1/2 [Filtration efficiency: 99.9%] AD  Oil mist density at outlet: 2,000 450C 1/2, 3/4 3 Max. 0.004 mg/m (ANR) GD 0.0032 ppm] ≈ [ 3,700 550C 3/4, 1 Piping support 1 type / 6,000 650 1, 1 2 AMF 1 / 12,000 850 1 , 2 2 8,000 801 50(2B) flange AMF650, 850 AMF150C to 550C 50(2B), 80(3B) 24,000 901 100(4B) flange 50(2B) flange 8,000 800 50(2B), 80(3B) 24,000 900 Free 100(4B) flange standing 100(4B), 150(6B) type 1000 40,000 flange 143 Courtesy of Steven Engineering, Inc.-230 Ryan Way, 258-9200-www.stevenengineering.com San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) South

4 P0141-P0220-E.qxd 08.11.6 1:48 PM Page 144 Compressed Air Cleaning Filter Series Series AM /AFF  Water Nominal Oil mist density removal Series filtration rating at outlet Smell Page rate  Water Separator Eliminates water droplets in the Series — — — 99% P.145 compressed air. AMG Water Separator  Main Line Filter m 3 μ Eliminates impurities such as Series (Filtration — P.153 oil and foreign matter, etc. in efficiency: AFF compressed air. 99%)  Mist Separator m 0.3 μ 3 1 mg/m (ANR) Eliminates oil mist in Series (Filtration P.161 0.8 ppm) ≈ ( compressed air or rust sized efficiency: AM (after oil saturation) μ m or more, and foreign 0.3 99.9%) matter such as carbon. —  Micro Mist Separator m 0.01 μ Eliminates foreign matter Series (Filtration P.169 m or more, or oil μ sized 0.01 efficiency: AMD particles in an aerosol state. 99.9%) 3 0.1 mg/m (ANR) — 0.08 ppm) ( ≈ Solid/Oil Separator  Micro Mist Separator with (after oil saturation) μ m 0.3 + 0.01 Pre-filter Series (Filtration P.179 Oil separator, which incorporates efficiency: AMH pre-filter (equivalent to the AM 99.9%) series) into micro mist separator.  Super Mist Separator Captures foreign matter sized 3 Series (ANR) 0.01 mg/m Reduces P.187 0.01 μ m or more and adsorbs AME 0.008 ppm) ≈ ( oil smell. oil particles in an aerosol state. 0.01 m μ (Filtration efficiency:  Odor Removal Filter 99.9%) Eliminates odor from 3 Deodorizes Series 0.004 mg/m (ANR) P.195 compressed air. oil smell. AMF ( 0.0032 ppm) ≈ Deodorizer P.204 Modular Connection Examples P.206 How to Order Bowl Assembly    Seal material: Fluororubber Degreasing wash, IN-OUT reversal direction Refer to white vaseline “How to   For medium air pressure Drain guide 1/4 female threaded Order” of  With element service indicator Options  With differential pressure switch (with indicator) respective  With differential pressure switch (with indicator) (125 VAC, 30 VDC) models. (30 VDC) ∗   With differential pressure gauge White vaseline specifications , Possible to control product s service life Using white vaseline for lubricant. by monitoring the clogged element.  With differential pressure gauge,  Auto drain type, drain guide IN-OUT flange specifications Flange piping connection and clogged P.210 Made to Order Drain piping is possible by auto drain type. element confirmation are possible.   With IN-OUT flange With differential pressure switch ∗ Flange piping connection is possible. (with indicator) Allows visual confirmation of differential pressure which indicates the element life. The built-in contact enables remote control. Applicable only to the AFF37B, 75B, AM  650 and 850. ∗ Clean Series Cotter-free, Fluorine-free Series Usable inside a clean room. Eliminates the effects on a color CRT by copper ion or Special Specifications P.210 fluoric resin, etc. Auto Drain Valve, Motor Operated Auto Drain, Heavy Duty Auto Drain, Differential Pressure Gauge P.276 Related Products P.216 Specific Product Precautions P.220 Discontinued Model and Equivalent Model 144 Courtesy of Steven Engineering, Inc.-230 258-9200-www.stevenengineering.com Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) Ryan

5 RoHS-AMG.qxd 10.7.26 5:57 PM Page 1 Water Separator RoHS AMG Series HAA Model HAW Model AMG850 AMG250C AMG350C AMG150C AMG550C AMG450C AMG650 Can remove water droplets in com- Note) pressed air. Use this product in ca- 300 6000 1500 3700 750 12000 2200 AT /min (ANR)) l Rated flow ( ses where “water must be avoided, 1 1 1 1 1 1 3 3 1 3 3 Por t size 11, 1 12 , , , , , , 2 2 2 2 4 4 4 8 8 8 4 IDF but not so dry as when an air dryer is Mass (kg) 1.4 0.38 0.55 0.9 2.1 4.2 10.5 IDU used”. Note) Max. flow at 0.7 MPa. Max. flow varies depending on the operating pressure. Refer to “Flow Characteristics” (page 148) IDFA Through the adoption of an element and “Maximum Air flow” (page 149). that is exclusively used for removing IDFB water droplets and the ample hous- ∗ water re- ing interior space, a 99% Specifications ∗∗ has been achieved. moval rate ID Compressed air Fluid 1.0 MPa Max. operating pressure ∗ 0.05 MPa Min. operating pressure IDG 1.5 MPa Proof pressure Caution ° 5 to 60 C Ambient and fluid temperature AMG 99% Water removal rate Water separator can remove water droplets, but 2 years or when pressure drop reached 0.1 MPa Element life it cannot remove moisture. AFF ∗ With auto drain: 0.1 MPa (N.O. type) or 0.15 MPa (N.C. type) Condition of inlet air ∗ Pressure: 0.7 MPa AM ° C Temperature: 25 Accessory Relative humidity: 100% AMD Applicable model AMG650 AMG850 AMG150C AMG250C AMG350C AMG450C AMG550C Liquid water content (Water droplet Bracket assembly 3 (ANR) content): 15 g/m AM-BM102 AM-BM103 AM-BM104 AM-BM101 BM56 BM57 AM-BM105 (with 2 mounting screws) AMH Compressed air flow: Rated flow of each model AME ∗∗ Water removal rate (%) = Caution Removed water (Water droplet) (g) x 100 AMF Inflowed water (Water droplet) (g) Be sure to read before handling. SF Refer to front matters 42 and 43 for Safety Instructions and pages 6 to Modular connection is possible 8 for Air Preparation Equipment Precautions. with AMG150C to 550C. SFD (For details, refer to page 204.) LLB AD  GD AMG150C to 550C AMG650/850 Symbol Symbol AMG AMG (Auto drain specifications) (Drain cock specifications) Made to Order (For details, refer to page 210.) 145 Courtesy of Steven Engineering, Inc.-230 Ryan Way, 258-9200-www.stevenengineering.com San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) South

6 176-AMG.qxd 10.5.7 10:49 AM Page 5 AMG Series How to Order AMG150C to 550C AMG 550C 10 Body size Made to Order 150C (“How to Order” and the applicable models are different from those shown on this page. Be sure to refer to “Made to Order”.) 250C 350C Description Symbol Page for details 450C — Nil — 3 ∗ 550C With IN-OUT flange P.212 X15 N.C., N.O. auto drain, drain piping type P.213 X26 Thread type 4 ∗ Type Symbol Option Rc Nil Description Symbol 1 ∗ G F — Nil NPT N Rubber material: Fluororubber F ∗ 1 Conforms to For medium air pressure (1.6 MPa) H 5 ∗ ISO1179-1. Drain guide 1/4 female threaded J IN-OUT reversal direction R Port size 6 ∗ white vaseline Degreasing wash, V Applicable body size Symbol Size ain piping and piping for a stop valve such ∗ 5Dr 250C 450C 550C 150C 350C as ball valve are required. 1/8 01 6 Only body/housing is degreasing washed. ∗ 1/4 02 3/8 03 4 1/2 04 ∗ Auto drain 3/4 06 Description Symbol 1 10 Drain cock (Without auto drain) Nil N.C. auto drain C N.O. auto drain D Accessory Description Symbol 4 Refer to “Drain Exhaust Specifications/ ∗ Option Combinations”. Nil — 2 (Only one drain exhaust method can be selected.) ∗ Bracket B racket is included, (but ∗ 2B Drain Exhaust Specifications/Option Combinations not assembled). : All types of drain exhaust specifications are available. (including drain guide, “J” specification) ∗ 3 The model with bracket : N.C. auto drain (“C” specification) is not available. is not available for -X15. : Both N.C. and N.O. auto drain (“C”, “D” specification) are not available. Nil H R V F Nil F H R V : Not available Options Symbol F: Rubber material: Fluororubber Symbol J: Drain guide 1/4 female threaded Symbol H: For medium air pressure (1.6 MPa) Can be pipied to the Fluororubber is used for the parts drain exhaust port. Can be used up to 1.6 MPa at such as O-ring and gasket. maximum. 1/4 female threaded Symbol V: Degreasing wash, Symbol R: IN-OUT reversal direction white vaseline Air flow in the separator is changed to Body/housing is degreasing washed. The right to left. lubrication grease for O-ring and gasket is (Air flow direction of the standard: Left changed to white vaseline. to right.) 146 258-9200-www.stevenengineering.com of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) Courtesy

7 176-AMG.qxd 10.5.7 10:49 AM Page 6 Water Separator Series AMG How to Order AMG650/850 650 10 AMG Body size Made to Order 650 (“How to Order” and the applicable models are different from those shown on this page. Be sure to refer to “Made to Order”.) 850 HAA Description Page for details Symbol HAW Nil — — Thread type 2 ∗ With IN-OUT flange P.212 X15 AT Symbol Type N.C., N.O. auto drain, drain piping type P.213 X26 Nil Rc White vaseline P.213 X12 IDF F G IDU NPT N 3 ∗ Option IDFA Description Symbol Port size Nil — Applicable body size 5 ∗ 1 IDFB Drain guide female threaded J 4 Symbol Size 850 650 IN-OUT reversal direction R 10 1 ain piping and piping for a stop valve such 5Dr ∗ ID 1 14 1 2 as ball valve are required. 20 2 Note) Element service indicator (symbol: T) is not IDG available as an option because water deposits inside the indicator could lead to Accessory malfunctions. AMG Description Symbol Nil — 3 ∗ 2 1 ∗ ∗ AFF Auto drain Bracket B Description Symbol ∗ racket is included, (but 1B 4 ∗ Drain cock (Without auto drain) Nil not assembled). AM ∗ 2 The model with bracket N.O. auto drain D is not available for -X15. 3 Refer to “Auto Drain Specifications/Option ∗ AMD Combinations”. 4 Body size 850 is equipped with a ball valve ∗ (Rc 3/8 female threaded). Mount a piping AMH adapter IDF-AP609 (page 205) to the ball valve if NPT 3/8 female threaded is required. AME AMF SF Note) Refer to “How to Order Bowl Assembly” on page 206. SFD LLB Auto Drain Specifications/Option Combinations : Not available : Available Option Auto drain specifications Applicable model Auto drain specifications/Option  AD AMG850 DJR AMG650 Auto drain specifications N.O. auto drain D 1 Drain guide J 4 GD Option IN-OUT reversal R direction 147 CA Courtesy Engineering, Inc.-230 Ryan Way, South San Francisco, of Steven 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com

8 176-AMG.qxd 10.5.7 10:49 AM Page 7 AMG Series Flow Characteristics (Representative values) Note) Compressed air over max. flow line in the table below may not meet the specifications of the product. AMG150C AMG450C AMG850 Max. flow line Max. flow line Max. flow line Pressure drop (MPa) Pressure drop (MPa) Pressure drop (MPa) 3 Air flow rate (m Air flow rate ( /min (ANR)) l /min (ANR)) /min (ANR)) Air flow rate ( l AMG250C AMG550C Max. flow line Max. flow line Pressure drop (MPa) Pressure drop (MPa) l /min (ANR)) Air flow rate ( l /min (ANR)) Air flow rate ( AMG350C AMG650 Max. flow line Max. flow line Pressure drop (MPa) Pressure drop (MPa) Air flow rate ( l Air flow rate ( /min (ANR)) l /min (ANR)) 148 Courtesy of Steven 258-9200-www.stevenengineering.com Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) Engineering,

9 176-AMG.qxd 10.5.7 10:50 AM Page 8 Water Separator Series AMG Construction AMG150C to 550C, AMG650 AMG850 q OUT IN OUT IN HAA HAW AT r IDF IDU w IDFA IDFB e ID IDG AMG AFF Component Parts Note) Refer to “How to Order Bowl Assembly” on page 206. Note Material No. Description AM Chrome treated Aluminum die-casted 1 Body Epoxy coating on ∗ 2 Aluminum die-casted Housing inner surface AMD Note) Sight glass is indicated in the figure for easy understanding of component parts. However, it differs from the actual — 3 Tempered glass Sight glass construction. Refer to dimensions on pages 150 to 152 for The AMG850 is aluminum casted. ∗ AMH details. Replacement Parts AME Model Applicable No. Material Description model AMG350C AMG850 AMG650 AMG150C AMG250C AMG550C AMG450C AMF AMG-EL450 Except option F AMG-EL650 AMG-EL550 AMG-EL850 AMG-EL350 AMG-EL150 AMG-EL250 Element Resin, 4 others assembly AMG-EL350-F AMG-EL450-F AMG-EL150-F AMG-EL250-F AMG-EL550-F For option F — — SF Element assembly: With gasket (1 pc.) and O-ring (1 pc.) ∗ ∗ Refer to back page 219 for replacement of auto drain. ∗ Element assemblies for Made to Order (X12, X15, X26) are same as those for standard (see the above table). SFD LLB Maximum Air Flow Model Selection Select a model in accordance with the following procedure taking the AD  inlet pressure and the max. air flow rate into consideration. (Example) Inlet pressure: 0.6 MPa GD 3 Max. air flow rate: 5 m /min (ANR) 1 . Obtain the intersecting point A of inlet pressure and max. air flow rate in the graph. 2 . The AMG650 is obtained when the max. flow line is above the in- terecting point A in the graph. Note) Make sure to select a model that has the max. flow line above the obtained intersecting point. With a model that has the max. /min (ANR)) 3 flow line below the obtained intersecting point, the flow rate will be exceeded, thus leading to a problem such as being unable to satisfy the specifications. Max. air flow rate (m Inlet pressure (MPa) 149 Courtesy of Steven Engineering, Inc.-230 Ryan 258-9200-www.stevenengineering.com South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) Way,

10 176-AMG.qxd 10.5.7 10:50 AM Page 9 Series AMG Dimensions AMG150C to 550C Auto drain C: With auto drain (N.C.) D: With auto drain (N.O.) P Q S R Drain cock Gray: N.C. Black: N.O. F O 34 ø10 One-touch fitting Combination of D: With auto drain (N.O.) D and H: For medium air pressure I L Bracket T (Accessory) N K M U V ø J Note) OUT IN Width across 20 flats 17 1/4 female threaded Note) 23 for AMG250C. C Option H A J: Drain guide 1/4 female threaded EB Drain port G Width across 20 M5 flats 24 1/4 female threaded space Maintenance (mm) Bracket related dimensions Model Port size B C D E F G A P O I N V R M L Q U T H K S J 161 20 10 63 6 63 12 70 99 10 6 54 6 4.5 1.6 176 5 23 35 26 10 56 1/8, 1/4 AMG150C 175 5 10 24 40 66 193 8 14 2 6 66 10 6 113 28 12 80 76 6 76 23 1/4, 3/8 AMG250C 207 145 34 90 28 14 95 7 90 5 8 7 10 80 80 225 18 12 50 7 23 2.3 3/8, 1/2 AMG350C 228 23 88 9 18 111 166 106 50 9 9 9 55 10 3.2 15 10 90 249 20 31 106 1/2, 3/4 AMG450C 262 10 24 23 126 15 200 3.2 122 102 122 9 60 33 9 15 9 18 281 100 65 10 3/4, 1 AMG550C 150 Courtesy of Steven Engineering, Inc.-230 Ryan Way, South 258-9200-www.stevenengineering.com Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) San

11 176-AMG.qxd 10.5.7 10:50 AM Page 10 Series AMG Water Separator Dimensions AMG650 Auto drain D: With auto drain (N.O.) 180 76 HAA 12 HAW Drain cock: Black 4.5 AT IDF 34 IDU 160 136 IDFA ø10 One-touch fitting IDFB Option ID J: Drain guide 1/4 female threaded IDG 160 150 AMG 20 Bracket 85 (Accessory) 15 11 AFF AM 40 32 Width across OUT IN 20 AMD flats 24 1/4 female threaded AMH 253 AME 337 314 AMF SF SFD LLB 10 23 Drain port M5  AD GD space Maintenance 151 258-9200-www.stevenengineering.com of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) Courtesy

12 P0141-P0220-E.qxd 08.11.6 1:48 PM Page 152 AMG Series Dimensions AMG850 Auto drain D: With auto drain (N.O.) for AMG850 220 110 6 18 23 220 184 3/8 female threaded Bracket 220 (Accessory) 180 24 120 15 13 30 42 OUT IN 348 461 464 58 Drain 10 Rc 3/8 female threaded space Maintenance 152 Courtesy of Steven 258-9200-www.stevenengineering.com Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) Engineering,

13 RoHS-AFF.qxd 10.7.26 5:57 PM Page 1 Main Line Filter RoHS Series AFF HAA Model HAW AFF2C AFF4C AFF8C AFF11C AFF22C AFF37B AFF75B AFF75A AFF125A AFF150A AFF220A Model Can remove impurities such as oil, Note) Rated flow water and foreign matter in com- AT 300 6000 750 2200 1500 22000 28000 42000 12000 12000 3700 /min (ANR)) l ( pressed air and can improve the 50(2B) 80(3B) 100(4B) 100(4B) IDF function of a dryer in the down- 1 1 1 1 1 3 3 3 1 1 3 size Por t 1 21 11, , , , , 2 4 8 8 8 4 4 2 , , 4 2 2 JIS 10K FF flange IDU stream, extend the life of precision filter, and prevent trouble with the Mass (kg) 4.2 0.9 1.4 2.1 0.55 72 10.5 87 50 0.38 52 IDFA equipment. Note) Max. flow at 0.7 MPa. Max. flow varies depending on the operating pressure. Modular connection is possible IDFB Refer to “Flow Characteristics” (page 156) and “Maximum Air Flow” below. with AFF2C to 22C. (For details, refer to page 204.) ID Specifications IDG Compressed air Fluid 1.0 MPa Max. operating pressure ∗ AMG 0.05 MPa Min. operating pressure 1.5 MPa Proof pressure ° 5 to 60 C Ambient and fluid temperature AFF 3 μ m (Filtration efficiency: 99%) Nominal filtration rating 2 years (1 year for A type) or when pressure drop reached 0.1 MPa Element life AM With auto drain: 0.1 MPa (N.O. type) or 0.15 MPa (N.C. type) ∗ AMD Accessory/For AFF2C to 22C, AFF37B/75B AFF2C to 22C AMH Applicable model AFF11C AFF75B AFF37B AFF22C AFF8C AFF4C AFF2C Bracket assembly BM57 AM-BM105 AM-BM104 AM-BM103 AM-BM102 AM-BM101 BM56 (with 2 mounting screws) AME AMF Accessory/For AFF75A to 220A Applicable model AFF220A AFF150A AFF75A AFF125A SF Auto drain (2 pcs. each) AD402-03-2 Pressure gauge (2 pcs. each) G46-15-02 SFD Companion flange (2 pcs. each) 100(4B)JIS 10K FF flange 50(2B)JIS 10K FF flange 80(3B)JIS 10K FF flange Anchor bolt (3 pcs. each) AI-2S LLB AD  AFF37B/75B AFF75A to 220A Model Selection Maximum Air Flow JIS Symbol JIS Symbol Max. flow line Select a model in accordance with the GD AFF AFF following procedure taking the inlet pressure and the max. air flow rate into consideration. (Example) Inlet pressure: 0.6 MPa 3 /min Max. air flow rate: 5 m (Auto drain specifications) (Drain cock specifications) (ANR) . Obtain the intersecting point A of inlet 1 pressure and max. air flow rate in the /min (ANR)) graph. 3 . The AFF37B is obtained when the max. 2 Made to Order flow line is above the intersecting point A (For details, refer to page 210.) in the graph. Caution Note) Make sure to select a model that has the max. flow line above the Max. air flow rate (m obtained intersecting point. With a Be sure to read before han- model that has the max. flow line dling. below the obtained intersecting Refer to front matters 42 and Inlet pressure (MPa) point, the flow rate will be excee- 43 for Safety Instructions and ded, thus leading to a problem such as being unable to satisfy the pages 6 to 8 for Air Preparation specifications. Equipment Precautions. 153 Courtesy 258-9200-www.stevenengineering.com Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) of Steven

14 176-AFF.qxd 10.5.7 11:10 AM Page 2 AFF Series How to Order AFF2C to 22C 10 AFF 22C Body size Thread type Applicable compressor Made to Order Symbol Type Symbol output (guide) (“How to Order” and the applicable models are different from those shown Rc Nil on this page. Be sure to refer to “Made to Order”.) 2.2 kW 2C 1 ∗ G F 3.7 kW 4C Symbol Description Page for details NPT N 7.5 kW — Nil 8C — ∗ 1 Conforms to 11 kW With differential pressure gauge (GD40-2-01) 11C P.211 X6 ISO1179-1. 3 ∗ 22 kW With IN-OUT flange 22C P.212 X15 With differential pressure gauge (GD40-2-01) Port size P.212 X17 3 ∗ and IN-OUT flange Accessory Applicable body size N.C., N.O. auto drain, drain piping type P.213 Symbol Size X26 Description Symbol 11C 22C 4C 2C 8C — Nil 1/8 01 4 ∗ Option 2 ∗ Bracket B 1/4 02 Description Symbol 3/8 03 ∗ 2B racket is included, — Nil (but not assembled). 1/2 04 Rubber material: Fluororubber F ∗ 3 The model with 3/4 06 For medium air pressure (1.6 MPa) H bracket is not available 1 10 5 ∗ Drain guide 1/4 female threaded J for -X15 and -X17. IN-OUT reversal direction R 6, Note) ∗ Drain Exhaust Specifications/Option Combinations With differential pressure switch (125 VAC, 30 VDC) S 6 ∗ : All types of drain exhaust specifications are available. (including drain guide, With differential pressure switch (30 VDC) U “J” specification) With element service indicator T : N.C. auto drain (“C” specification) is not available. 7 ∗ white vaseline Degreasing wash, V : Both N.C. and N.O. auto drain (“C”, “D” specification) are not available. ain piping and piping for a stop valve such as ball valve are required. ∗ 5Dr Nil F V U S R H T ∗ 6 Differential pressure gauge is included, (but not assembled). Note Nil 7 Only body/housing is degreasing washed. ∗ F Note) Order “U” if conformity to the EU directive is required. H 4 ∗ Auto drain Note R Description Symbol S Drain cock (Without auto-drain) Nil U Note Note N.C. auto drain C T N.O. auto drain D V ∗ Refer to “Drain Exhaust Specifications/ 4 Note: Only one drain exhaust method can be selected. Option Combinations”. : Not available (Only one drain exhaust method can be selected.) Options Symbol J: Drain guide 1/4 female threaded Symbol H: For medium air pressure Symbol F: Rubber material: Fluororubber (1.6 MPa) Can be pipied to the Fluororubber is used for the parts drain exhaust port. Can be used up to 1.6 MPa at such as O-ring and gasket. maximum. 1/4 female thread Symbol U: With differential pressure Symbol S: With differential pressure Symbol R: IN-OUT reversal direction switch (with indicator) switch (with indicator) Air flow in the separator is changed to Saturation of the Saturation of the right to left. 0.1 0.1 .05 .05 0.15 0.15 0.2 0.2 MPa MPa SMC SMC separator can be separator can be (Air flow direction of the standard: Left observed visually or by observed visually or by to right.) an electrical signal. an electrical signal. (Element life check) (Element life check) Symbol T: With element service indicator ∗ ∗ The rated contact voltage is different The rated contact voltage is different from “U”. from “S”. Saturation of the Max. contact capacity: 10 VA AC, 10 W DC Max. contact capacity: 10 W DC separator can be Rated contact voltage (max. operating Rated contact voltage (max. operating Pressure observed visually. current): 30 V DC (0.33 A) current): 125 V AC (0.08 A), 30 V DC (0.33 A) drop (Element life check) 0.1 MPa Symbol V: Degreasing wash, white vaseline Body/housing is degreasing washed. The Reed switch Reed switch lubrication grease for O-ring and gasket is changed to white vaseline. 154 Courtesy of Steven 258-9200-www.stevenengineering.com Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) Engineering,

15 176-AFF.qxd 10.5.7 11:10 AM Page 3 AFF Series Main Line Filter How to Order AFF37B/75B 37B 10 AFF Body size Made to Order (“How to Order” and the applicable models are different from those shown on this Applicable compressor Symbol page. Be sure to refer to “Made to Order”.) output (guide) HAA Description Symbol Page for details 37 kW 37B HAW Nil — — 75B 75 kW With differential pressure gauge (GD40-2-01) P.211 X6 AT With differential pressure switch (With indicator, P.211 X37 Thread type 125 VAC, 30 VDC) IDF 2 ∗ Type Symbol P.212 With IN-OUT flange X15 IDU Nil Rc With differential pressure gauge (GD40-2-01) P.212 X17 2 ∗ and IN-OUT flange F G IDFA N.C., N.O. auto drain, drain piping type P.213 X26 NPT N White vaseline specifications P.213 X12 IDFB Port size 3 ∗ Option Applicable body size Size Symbol Symbol Description ID 37B 75B Nil — 1 10 5 ∗ 1 1 Drain guide female threaded J 1 14 4 2 IDG IN-OUT reversal direction 20 R 2 With element service indicator T AMG ain piping and piping for a stop valve 5Dr ∗ Accessory such as ball valve are required. Description Symbol AFF 3 ∗ Nil — Auto drain 2 1 ∗ ∗ Bracket B Description Symbol AM 4 ∗ 1B ∗ racket is included, (but Drain cock (Without auto drain) Nil not assembled). N.O. auto drain D ∗ 2 The model with bracket AMD ∗ 3 Refer to “Auto Drain Specifications/Option is not available for -X15 Combinations”. and -X17. ∗ 4 Body size 75B is equipped with a ball valve AMH (Rc 3/8 female threaded). Mount a piping adapter IDF-AP609 (page 205) to the ball valve if NPT 3/8 female threaded is required. AME Note) Refer to “How to Order Bowl Assembly” on page 206. AMF SF Auto Drain Specifications/Option Combinations : Available : Not available Auto drain specifications Option Applicable model Auto drain specifications/Option SFD R DJT AFF37B AFF75B N.O. auto drain Auto drain specifications D LLB 1 Drain guide J 4 Option IN-OUT reversal direction R With element service indicator T  AD GD AFF75A to 220A 20 75A AFF D Made to Order Standard size (“How to Order” and the applicable models are different (Applicable compressor) from those shown on this page. Be sure to refer to Compressor output Symbol “Made to Order”.) 75 kW 75A Page for details Description Symbol 125A 110 to 125 kW Nil — — 150A 150 kW Mist separator for high flow rate P.214 X13 220A 180 to 220 kW (Nominal filtration rating: 0.3 μ m) Accessory size Port Description Symbol Applicable body size — Nil Size Symbol 125A 150A 220A 75A Auto drain D 20 50(2B) JIS 10K FF flange Pressure gauge G 30 80(3B) JIS 10K FF flange Companion flange F flange 100 ( 4B JIS 10K FF ) 40 L Anchor bolt 155 CA Courtesy Engineering, Inc.-230 Ryan Way, South San Francisco, of Steven 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com

16 176-AFF.qxd 10.5.7 11:10 AM Page 4 Series AFF Flow Characteristics (Representative values) /Select the model taking the max. flow capacity into consideration. (Element oil saturation) Note) Compressed air over max. flow line in the table below may not meet the specifications of the product. AFF22C AFF75A AFF2C Max. flow line Max. flow line Max. flow line Pressure drop (MPa) Pressure drop (MPa) Pressure drop (MPa) 3 Air flow rate ( l l /min (ANR)) /min (ANR)) Air flow rate (m Air flow rate ( /min (ANR)) AFF4C AFF37B AFF125A Max. flow line Max. flow line Max. flow line Pressure drop (MPa) Pressure drop (MPa) Pressure drop (MPa) 3 Air flow rate (m l /min (ANR)) /min (ANR)) Air flow rate ( l /min (ANR)) Air flow rate ( AFF150A AFF8C AFF75B Max. flow line Max. flow line Max. flow line Pressure drop (MPa) Pressure drop (MPa) Pressure drop (MPa) 3 3 /min (ANR)) Air flow rate (m /min (ANR)) /min (ANR)) Air flow rate (m Air flow rate ( l AFF11C AFF220A Max. flow line Max. flow line Pressure drop (MPa) Pressure drop (MPa) 3 /min (ANR)) /min (ANR)) l Air flow rate (m Air flow rate ( 156 Courtesy of Steven 258-9200-www.stevenengineering.com Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) Engineering,

17 176-AFF.qxd 10.5.7 11:10 AM Page 5 Main Line Filter Series AFF Construction AFF2C to 22C, AFF37B AFF75B q OUT IN OUT IN HAA HAW AT IDF r IDU w IDFA IDFB e ID IDG AMG AFF Component Parts Material Note No. Description Note) Refer to “How to Order Bowl Assembly” on page 206. Chrome treated AM 1 Body Aluminum die-casted ∗ Epoxy coating on inner surface 2 Housing Aluminum die-casted Note) Sight glass is indicated in the figure for easy understanding — 3 Sight glass Tempered glass AMD of component parts. However, it differs from the actual ∗ The AFF75B is aluminum casted. construction. Please refer to pages 158 through to 160 for details. AMH Replacement Parts Model Applicable No. Description Material AME model AFF11C AFF2C AFF37B AFF4C AFF22C AFF8C AFF75B AFF-EL11B AFF-EL75B AFF-EL8B AFF-EL4B AFF-EL22B AFF-EL2B AFF-EL37B Except option F Element Cotton paper, 4 others assembly AFF-EL11B-F — AFF-EL22B-F — AFF-EL2B-F AFF-EL8B-F AFF-EL4B-F For option F AMF Element assembly: With gasket (1 pc.) and O-ring (1 pc.) ∗ Refer to page 219 for replacement of auto drain. ∗ SF ∗ Element assemblies for Made to Order (X6, X12, X15, X17, X26, X37) are same as those for standard (see the above table). SFD AFF75A to 220A LLB AD  OUT GD (OUT side) Guage port Drain IN Gauge port (IN side) Component Parts Note Material No. Description 1 SGP-E, SS400 Case 2 SS400 Cover Replacement Parts Drain Model Qty. No. Material Description AFF75A AFF125A AFF150A AFF220A — EC900-003N EC800-003N EC700-003N 3 Element 1 AL-34S AL-35S AL-33S NBR 4 Seal 1 157 CA Courtesy Engineering, Inc.-230 Ryan Way, South San Francisco, of Steven 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com

18 176-AFF.qxd 10.5.7 11:10 AM Page 6 AFF Series Dimensions AFF2C to 22C Auto drain C: With auto drain (N.C.) D: With auto drain (N.O.) P Q S R Drain cock Gray: N.C. 34 Black: N.O. F O ø10 One-touch fitting Combination of D: With auto drain (N.O.) and H: For medium air pressure D Note) I 20 L Bracket T (Accessory) Width across N K 1/4 female threaded flats 17 M U V ø Note) 23 for AFF4C. J Option IN OUT J: Drain guide 1/4 female threaded C H A Width across 20 flats 24 1/4 female threaded S, U: With differential pressure switch (with indicator) Y EB Drain port G Z M5 OUT IN space Maintenance T: With element service indicator W X IN OUT (mm) Element Differential pressure service Bracket related dimensions indicator related switch related Port size Model F B D C G E A dimensions dimensions Z N V P T M L Q U Y O K R X H J S W I 70 56 24 176 20 4.5 37 10 5 32 26 63 41 6 1.6 23 63 6 54 99 10 12 35 10 6 161 1/8, 1/4 AFF2C 2 80 37 113 6 66 14 66 10 5 6 36 41 40 24 27 12 8 28 10 76 193 6 76 23 175 1/4, 3/8 AFF4C 32 7 80 7 95 8 34 28 5 80 2.3 7 12 10 37 90 42 23 41 90 145 18 225 14 50 207 3/8, 1/2 AFF8C 37 10 10 9 9 106 18 50 43 23 31 37 41 106 88 166 9 20 90 9 15 3.2 249 55 111 228 1/2, 3/4 AFF11C 281 51 9 33 122 3.2 102 41 65 15 200 60 18 24 39 10 100 122 9 9 37 10 126 23 15 262 3/4, 1 AFF22C 158 Courtesy of Steven Engineering, Inc.-230 Ryan Way, South 258-9200-www.stevenengineering.com Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) San

19 176-AFF.qxd 10.5.7 11:10 AM Page 7 AFF Main Line Filter Series Dimensions AFF37B Auto drain D: With auto drain (N.O.) 180 76 HAA 12 Drain cock: Black HAW 4.5 AT 34 IDF IDU 160 136 ø10 One-touch fitting IDFA IDFB Option J: Drain guide 1/4 female threaded ID IDG 160 150 AMG 20 Bracket 85 (Accessory) 15 11 AFF Width across 20 AM 40 flats 24 32 1/4 female IN OUT threaded AMD T: With element service indicator AMH 55 253 AME 337 314 37 AMF SF IN OUT SFD LLB 10 23 Drain port M5 AD  GD space Maintenance 159 CA Courtesy Engineering, Inc.-230 Ryan Way, South San Francisco, of Steven 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com

20 P0141-P0220-E.qxd 08.11.6 1:51 PM Page 160 AFF Series Dimensions AFF75B Auto drain 220 110 D: With auto drain (N.O.) 6 18 for AFF75B 184 220 23 3/8 female threaded Bracket 220 (Accessory) 180 120 24 15 Option 13 T: With element service indicator 30 42 OUT IN 348 OUT IN 461 464 58 Drain 10 Rc 3/8 female threaded space Maintenance AFF75A to 220A 3 x ø20 holes For foundation bolt OUT Label Drain ORIENTATION IN (mm) Model Port size C D F B G A E ø 50(2B)JIS10K FF flange 505 184 380 935 1125 265 AFF75A 200 (8B) Drain 80(3B)JIS10K FF flange 505 380 1125 935 265 184 AFF125A 200 (8B) 100(4B)JIS10K FF flange 540 265 450 1178 980 236 AFF150A 250 (10B) 325 282 500 1291 1070 670 100(4B)JIS10K FF flange AFF220A 300 (12B) 160 Courtesy 258-9200-www.stevenengineering.com Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) of Steven

21 RoHS-AM.qxd 10.7.26 5:58 PM Page 1 Mist Separator RoHS AM Series HAA Model HAW AM450C AM650 AM550C AM350C AM250C Model AM150C AM850 Can remove oil mist in compressed Note) air and separate and remove 750 2200 1500 6000 3700 12000 300 AT l Rated flow ( /min (ANR)) particles such as rust or carbon of 3 3 1 3 1 1 1 3 1 1 1 1 size Por t 11, 12 , , , , , , 8 8 2 8 2 4 2 4 2 4 4 IDF more than 0.3 μ m. Mass (kg) 1.4 0.9 4.2 0.55 2.1 10.5 0.38 IDU Note) Max. flow at 0.7 MPa. Modular connection is possible Max. flow varies depending on the operating pressure. IDFA Refer to “Flow Characteristics” (page 164) and “Maximum Air Flow” (page 165). with AM150C to 550C. Note) Refer to “Made to Order” (page 214) for high flow type of AM850 or more. (For details, refer to page 204.) IDFB ID Specifications IDG Compressed air Fluid 1.0 MPa Max. operating pressure 1 ∗ 0.05 MPa Min. operating pressure AMG 1.5 MPa Proof pressure C 5 to 60 ° Ambient and fluid temperature AFF m (Filtration efficiency: 99.9%) 0.3 μ Nominal filtration rating 3 2 ∗ (ANR) ( ≈ 0.8 ppm) Max. 1 mg/m Oil mist density at outlet AM 2 years or when pressure drop reached 0.1 MPa Element life ∗ 1 With auto drain: 0.1 MPa (N.O. type) or 0.15 MPa (N.C. type) 3 AMD (ANR) blown out by compressor. 2 Oil mist density at 30 mg/m ∗ AMH Accessory AM650/850 AM150C to 550C Applicable model AM150C AM250C AM350C AM450C AM550C AM650 AM850 AME Bracket assembly AM-BM104 AM-BM103 AM-BM102 BM56 AM-BM101 BM57 AM-BM105 (with 2 mounting screws) AMF Symbol Symbol AM AM SF Caution SFD (Drain cock specifications) (Auto drain specifications) Be sure to read before handling. Refer to front matters 42 and 43 for Safety Instructions and pages 6 to LLB 8 for Air Preparation Equipment Precautions.  AD Made to Order GD (For details, refer to page 210.) 161 CA Courtesy Engineering, Inc.-230 Ryan Way, South San Francisco, of Steven 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com

22 176-AM.qxd 10.5.7 11:11 AM Page 2 Series AM How to Order AM150C to 550C 10 AM 550C Body size Applicable compressor Made to Order Thread type Symbol output (guide) (“How to Order” and the applicable models are different from those Symbol Type shown on this page. Be sure to refer to “Made to Order”.) 2.2 kW 150C Rc Nil 3.7 kW 250C Description Symbol Page for details 1 ∗ G F 7.5 kW 350C — Nil — NPT N 11 kW 450C With differential pressure gauge (GD40-2-01) P.211 X6 ∗ 1 Conforms to 22 kW 550C With IN-OUT flange P.212 X15 ISO1179-1. With differential pressure gauge (GD40-2-01) size Port P.212 X17 3 ∗ and IN-OUT flange Accessory Applicable body size N.C., N.O. auto drain, drain piping type P.213 X26 Symbol Size Description Symbol 550C 150C 250C 450C 350C 4 — Nil ∗ 1/8 01 Option 2 ∗ Bracket B 1/4 02 Description Symbol 3/8 03 ∗ 2B racket is included, — Nil (but not assembled). 1/2 04 Rubber material: Fluororubber F ∗ 3 The model with bracket 3/4 06 For medium air pressure (1.6 MPa) H is not available for -X15 1 10 5 ∗ Drain guide 1/4 female threaded J and -17. IN-OUT reversal direction R 6, Note) ∗ Drain Exhaust Specifications/Option Combinations With differential pressure switch (125 VAC, 30 VDC) S 6 ∗ With differential pressure switch (30 VDC) : All types of drain exhaust specifications are available. (including drain guide, U “J” specification) Element service indicator T : N.C. auto drain (“C” specification) is not available. 7 ∗ white vaseline Degreasing wash, V : Both N.C. and N.O. auto drain (“C”, “D” specification) are not available. ain piping and piping for a stop valve such as ball valve are required. 5Dr ∗ Nil T U S R H F V 6 Differential pressure gauge is included, (but not assembled). ∗ Note Nil 7 Only body/housing is degreasing washed. ∗ Note) Order “U” if conformity to the EU directive is required. F H 4 ∗ Auto drain Note R Description Symbol S Drain cock (Without auto drain) Nil Note Note U N.C. auto drain C T N.O. auto drain D V Refer to “Drain Exhaust Specifications/ 4 ∗ Note: Only one drain exhaust method can be selected. Option Combinations”. : Not available (Only one drain exhaust method can be selected.) Options Symbol F: Rubber material: Fluororubber Symbol H: For medium air pressure Symbol J: Drain guide 1/4 female threaded (1.6 MPa) Can be pipied to the Fluororubber is used for the parts drain exhaust port. Can be used up to 1.6 MPa at such as O-ring and gasket. maximum. 1/4 female threaded Symbol R: IN-OUT reversal direction Symbol U: With differential pressure Symbol S: With differential pressure switch (with indicator) switch (with indicator) Air flow in the separator is changed to Saturation of the Saturation of the right to left. 0.1 0.1 .05 .05 0.15 0.15 0.2 0.2 MPa MPa SMC SMC separator can be separator can be (Air flow direction of the standard: Left observed visually or by observed visually or by to right.) an electrical signal. an electrical signal. (Element life check) (Element life check) Symbol T: With element service indicator ∗ The rated contact voltage is different ∗ The rated contact voltage is different from “S”. from “U”. Saturation of the Max. contact capacity: 10 W DC Max. contact capacity: 10 VA AC, 10 W DC separator can be Rated contact voltage (max. operating Rated contact voltage (max. operating Pressure observed visually. current): 125 V AC (0.08 A), 30 V DC (0.33 A) current): 30 V DC (0.33 A) drop (Element life check) 0.1 MPa Symbol V: Degreasing wash, white vaseline Body/housing is degreasing washed. The Reed switch Reed switch lubrication grease for O-ring and gasket is changed to white vaseline. 162 Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San 258-9200-www.stevenengineering.com CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) Francisco,

23 176-AM.qxd 10.5.7 11:11 AM Page 3 AM Mist Separator Series How to Order AM650/850 650 10 AM Body size Made to Order Applicable compressor Symbol (“How to Order” and the applicable models are different from those shown on output (guide) this page. Be sure to refer to “Made to Order”.) HAA 650 37 kW HAW Page for details Description Symbol 850 75 kW Nil — — Thread type AT P.211 With differential pressure gauge (GD40-2-01) X6 Type Symbol With differential pressure switch (With indicator, X37 P.211 IDF Nil Rc 125 VAC, 30 VDC) IDU 2 ∗ F G P.212 X15 With IN-OUT flange NPT N With differential pressure gauge (GD40-2-01) P.212 X17 IDFA 2 ∗ and IN-OUT flange X26 N.C., N.O. auto drain, drain piping type P.213 size Port IDFB X12 White vaseline specifications P.213 Applicable body size Symbol Size 650 850 3 ∗ ID Option 1 10 1 Description Symbol 1 14 2 Nil — IDG 20 2 5 ∗ 1 Drain guide female threaded J 4 R IN-OUT reversal direction AMG Accessory With element service indicator T Description Symbol ain piping and piping for a stop valve 5Dr ∗ AFF — Nil such as ball valve are required. 1 ∗ Bracket B racket is included, 1B ∗ AM 3 ∗ Auto drain (but not assembled). Description Symbol ∗ 2 The model with bracket 4 ∗ AMD Drain cock (Without auto drain) Nil is not available for -X15 and -X17. N.O. auto drain D ∗ Refer to “Auto Drain Specifications/Option 3 AMH Combinations”. ∗ 4 Body size 850 is equipped with a ball valve AME (Rc 3/8 female threaded). Mount a piping adapter IDF-AP609 (page 205) to the ball valve if NPT 3/8 female threaded is required. AMF SF Note) Refer to “How to Order Bowl Assembly” on page 206. SFD LLB Auto Drain Specifications/Option Combinations : Not available : Available Applicable model Auto drain specifications Option Auto drain specifications/Option AD  DJT AM650 AM850 R Auto drain specifications N.O. auto drain D 1 Drain guide J GD 4 Option IN-OUT reversal direction R With element service indicator T 163 Courtesy of Steven Engineering, 258-9200-www.stevenengineering.com Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) Inc.-230

24 176-AM.qxd 10.5.7 11:11 AM Page 4 AM Series Flow Characteristics (Representative values) (Element oil saturation) Note) Compressed air over max. flow line in the table below may not meet the specifications of the product. AM450C AM850 AM150C Max. flow line Max. flow line Max. flow line Pressure drop (MPa) Pressure drop (MPa) Pressure drop (MPa) 3 /min (ANR)) Air flow rate ( l /min (ANR)) Air flow rate (m l /min (ANR)) Air flow rate ( AM250C AM550C Max. flow line Max. flow line Pressure drop (MPa) Pressure drop (MPa) Air flow rate ( l Air flow rate ( /min (ANR)) l /min (ANR)) AM650 AM350C Max. flow line Max. flow line Pressure drop (MPa) Pressure drop (MPa) /min (ANR)) Air flow rate ( l Air flow rate ( l /min (ANR)) 164 258-9200-www.stevenengineering.com of Steven Engineering, Inc.-230 Ryan Way, South San Courtesy CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) Francisco,

25 176-AM.qxd 10.5.7 11:11 AM Page 5 Mist Separator Series AM Construction AM150C to 550C, AM650 AM850 q OUT IN OUT IN HAA HAW AT IDF r IDU w IDFA IDFB e ID IDG AMG AFF Component Parts AM Material Note No. Description Note) Refer to “How to Order Bowl Assembly” on page 206. Chrome treated 1 Body Aluminum die-casted AMD ∗ Epoxy coating on inner surface 2 Housing Aluminum die-casted Note) Sight glass is indicated in the figure for easy understanding of — 3 Sight glass Tempered glass component parts. However, it differs from the actual AMH ∗ The AM850 is aluminum casted. construction. Refer to dimensions on pages 166 through to 168 for details. Replacement Parts AME Model Applicable No. Description Material model AM650 AM150C AM450C AM850 AM350C AM250C AM550C AMF AM-EL350 AM-EL650 AM-EL550 AM-EL150 AM-EL850 AM-EL250 AM-EL450 Except option F Element Glass fiber, 4 assembly others AM-EL150-F AM-EL550-F AM-EL350-F — AM-EL250-F — AM-EL450-F For option F SF ∗ Element assembly: With gasket (1 pc.) and O-ring (1 pc.) ∗ Refer to page 219 for replacement of auto drain. ∗ Element assemblies for Made to Order (X6, X12, X15, X17, X26, X37) are same as those for standard (see the above table). SFD LLB Model Selection Maximum Air Flow Max. flow line Select a model in accordance with the following procedure taking the  AD inlet pressure and the max. air flow rate into consideration. (Example) Inlet pressure: 0.6 MPa 3 GD /min (ANR) Max. air flow rate: 5 m 1 . Obtain the intersecting point A of inlet pressure and max. air flow rate in the graph. 2 . The AM650 is obtained when the max. flow line is above the inter- secting point A in the graph. Note) Make sure to select a model that has the max. flow line above the obtained intersecting point. With a model that has the max. /min (ANR)) flow line below the obtained intersecting point, the flow rate will 3 be exceeded, thus leading to a problem such as being unable to satisfy the specifications. Max. air flow rate (m Inlet pressure (MPa) 165 Courtesy of Steven Engineering, 258-9200-www.stevenengineering.com Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) Inc.-230

26 176-AM.qxd 10.5.7 11:11 AM Page 6 AM Series Dimensions AM150C to 550C Auto drain C: With auto drain (N.C.) D: With auto drain (N.O.) P Q S R Drain cock Gray: N.C. 34 Black: N.O. F O ø10 One-touch fitting Combination of D: With auto drain (N.O.) and H: For medium air pressure D Note) I 20 L Bracket T Width across (Accessory) N flats 17 K M 1/4 female threaded U V ø Note) 23 for AM250C. J Option IN OUT J: Drain guide 1/4 female threaded C H A Width across 20 flats 24 1/4 female threaded S, U: With differential pressure switch (with indicator) Y EB Drain port G Z M5 OUT IN space Maintenance T: With element service indicator W X OUT IN (mm) Differential Element pressure service Bracket related dimensions indicator related switch related Model Port size G C B F E D A dimensions dimensions V Z Y I X W S R Q J P O N H M K L U T 10 6 6 10 5 12 99 6 63 10 20 35 63 56 54 173 20 70 41 26 32 4.5 37 1.6 24 158 1/8, 1/4 AM150C 76 2 5 37 28 36 80 41 190 66 10 24 66 6 40 20 10 76 6 113 12 14 6 8 27 172 1/4, 3/8 AM250C 14 10 80 2.3 12 90 28 7 20 32 95 90 8 50 145 37 34 18 7 42 7 5 41 222 80 204 3/8, 1/2 AM350C 37 20 9 31 18 106 43 246 55 166 111 3.2 41 20 9 9 15 10 50 37 90 10 106 88 9 225 1/2, 3/4 AM450C 37 65 41 39 200 18 15 15 10 24 126 100 10 278 122 9 33 9 3.2 20 51 102 60 9 122 259 3/4, 1 AM550C 166 Courtesy of Steven Engineering, Inc.-230 Ryan Way, South 258-9200-www.stevenengineering.com Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) San

27 176-AM.qxd 10.5.7 11:11 AM Page 7 AM Series Mist Separator Dimensions AM650 Auto drain D: With auto drain (N.O.) 180 76 HAA 12 Drain cock: Black HAW 4.5 AT 34 IDF IDU 160 136 ø10 One-touch fitting IDFA IDFB Option J: Drain guide 1/4 female threaded ID IDG 160 150 AMG 20 Bracket 85 (Accessory) 15 11 AFF Width across 20 AM flats 24 40 32 1/4 female IN OUT threaded AMD AMH T: With element service indicator 55 253 AME 337 314 AMF 37 SF OUT IN SFD LLB 10 23 Drain port M5 AD  GD space Maintenance 167 CA Courtesy Engineering, Inc.-230 Ryan Way, South San Francisco, of Steven 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com

28 P0141-P0220-E.qxd 08.11.6 1:51 PM Page 168 AM Series Dimensions AM850 Auto drain 220 D: With auto drain (N.O.) 110 for AM850 6 18 23 184 220 3/8 female threaded Option T: With element service indicator Bracket 220 (Accessory) 180 24 120 15 13 30 IN OUT 42 OUT IN 348 461 464 58 Drain 10 Rc 3/8 female threaded space Maintenance 168 Courtesy of Steven Engineering, Inc.-230 Ryan Way, South 258-9200-www.stevenengineering.com Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) San

29 RoHS-AMD.qxd 10.7.26 5:58 PM Page 1 Micro Mist Separator RoHS AMD Series HAA Model HAW AMD350C AMD650 AMD450C AMD550C AMD250C AMD850 AMD150C Model Can separate and remove aerosol Note) state oil mist in compressed air and AT 1000 500 12000 2000 6000 3700 200 /min (ANR)) l Rated flow ( remove particles such as carbon or IDF m. μ dust of more than 0.01 3 3 1 1 3 1 3 1 1 1 1 1 11, 12 Por t size , , , , , 4 4 8 8 8 4 2 2 4 , 2 2 IDU Use this product as a pre-filter for compressed air for precision Mass (kg) 0.55 0.38 0.9 4.2 10.5 1.4 2.1 IDFA instruments or clean room requiring Note) Max. flow at 0.7 MPa. higher clean air. Max. flow varies depending on the operating pressure. IDFB Refer to “Flow Characteristics” (page 172) and “Maximum Air Flow” (page 171). ID Modular connection is possible Model/Free Standing Type with AMD150C to 550C. IDG AMD1000 Model AMD800 AMD900 (For details, refer to page 204.) /min (ANR)) Rated flow ( l 8000 24000 40000 AMG 50(2B), 80(3B), 100(4B)JIS 100(4B), 150(6B)JIS 50(2B)JIS Por t size 10K FF flange 10K FF flange 10K FF flange Mass (kg) 100 220 430 AFF AM Model/Piping Support Type Model AMD801 AMD901 AMD /min (ANR)) Rated flow ( l 8000 24000 Por t size 50(2B)JIS 10K FF flange 50(2B), 80(3B), 100(4B)JIS 10K FF flange AMH Mass (kg) 50 140 AME Specifications AMF Compressed air Fluid 1.0 MPa Max. operating pressure 1 ∗ 0.05 MPa Min. operating pressure SF 1.5 MPa Proof pressure C 5 to 60 ° Ambient and fluid temperature SFD m (Filtration efficiency: 99.9%) μ 0.01 Nominal filtration rating AMD650/850 AMD150C to 550C 3 2 ∗ Max. 0.1 mg/m ( ANR) Oil mist density at outlet 3 LLB (Before saturated with oil, less than 0.01 mg/m (ANR) ≈ 0.008 ppm) 2 years (1 year for flange type) Symbol Symbol Element life or when pressure drop reached 0.1 MPa AMD AMD AD  ∗ 1 With auto drain: 0.1 MPa (N.O. type) or 0.15 MPa (N.C. type) 3 (ANR) blown out by compressor. 2 Oil mist density at 30 mg/m ∗ GD (Auto drain specifications) (Drain cock specifications) Accessory Applicable model AMD150C AMD250C AMD350C AMD450C AMD550C AMD650 AMD850 Bracket assembly Made to Order AM-BM101 AM-BM102 AM-BM103 AM-BM104 AM-BM105 BM56 BM57 (with 2 mounting screws) (For details, refer to page 210.) Caution Be sure to read before handling. Refer to front matters 42 and 43 for Safety Instructions and pages 6 to 8 for Air Preparation Equipment Precautions. 169 Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San 258-9200-www.stevenengineering.com CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) Francisco,

30 176-AMD.qxd 10.5.10 9:35 AM Page 2 Series AMD How to Order AMD150C to 550C AMD 550C 10 Body size Thread type 150C Made to Order Symbol Type (“How to Order” and the applicable models are different from those shown 250C on this page. Be sure to refer to “Made to Order”.) Rc Nil 350C 1 ∗ G F Description Symbol Page for details 450C NPT N — Nil 550C — With differential pressure gauge (GD40-2-01) P.211 X6 1 Conforms to ∗ 3 ∗ ISO1179-1. With IN-OUT flange P.212 X15 With differential pressure gauge (GD40-2-01) size Port P.212 X17 3 ∗ and IN-OUT flange Accessory Applicable body size Symbol Size N.C., N.O. auto drain, drain piping type P.213 X26 150C 450C 550C 250C 350C Symbol Description — Nil 1/8 01 4 ∗ Option 2 ∗ Bracket 1/4 02 B Description Symbol 3/8 03 2B racket is included, ∗ — Nil 1/2 (but not assembled). 04 Rubber material: Fluororubber F ∗ 3 The model with bracket 3/4 06 For medium air pressure (1.6 MPa) H is not available for 1 10 5 ∗ Drain guide 1/4 female thread J -X15 and -X17. IN-OUT reversal direction R 6, Note) ∗ With differential pressure switch (125 VAC, 30 VDC) S Drain Exhaust Specifications/Option Combinations 6 ∗ With differential pressure switch (30 VDC) U : All types of drain exhaust specifications are available. (including drain guide, With element service indicator T “J” specification) 7 ∗ : N.C. auto drain (“C” specification) is not available. white vaseline Degreasing wash, V : Both N.C. and N.O. auto drain (“C”, “D” specification) are not available. ain piping and piping for a stop valve such as ball valve are required. ∗ 5Dr Nil V H R S U F T 6 Differential pressure gauge is included, (but not assembled). ∗ Note ∗ 7 Only body/housing is degreasing washed. Nil Note) Order “U” if conformity to the EU directive is required. F H 4 ∗ Auto drain Note R Symbol Description S Drain cock (Without auto drain) Nil U Note Note N.C. auto drain C T N.O. auto drain D V Refer to “Drain Exhaust Specifications/ 4 ∗ Note: Only one drain exhaust method can be selected. Option Combinations”. : Not available (Only one drain exhaust method can be selected.) Options Symbol H: For medium air pressure Symbol F: Rubber material: Fluororubber Symbol J: Drain guide 1/4 female threaded (1.6 MPa) Can be pipied to the Fluororubber is used for the parts drain exhaust port. Can be used up to 1.6 MPa at such as O-ring and gasket. maximum. 1/4 female threaded Symbol U: With differential pressure Symbol R: IN-OUT reversal direction Symbol S: With differential pressure switch (with indicator) switch (with indicator) Air flow in the separator is changed to Saturation of the Saturation of the right to left. 0.1 0.1 .05 .05 0.15 0.15 0.2 0.2 MPa MPa SMC SMC separator can be separator can be (Air flow direction of the standard: Left observed visually or by observed visually or by to right.) an electrical signal. an electrical signal. (Element life check) (Element life check) Symbol T: With element service indicator The rated contact voltage is different ∗ The rated contact voltage is different ∗ from “U”. from “S”. Saturation of the Max. contact capacity: 10 W DC Max. contact capacity: 10 VA AC, 10 W DC separator can be Rated contact voltage (max. operating Rated contact voltage (max. operating Pressure observed visually. current): 30 V DC (0.33 A) current): 125 V AC (0.08 A), 30 V DC (0.33 A) drop (Element life check) 0.1 MPa Symbol V: Degreasing wash, white vaseline Body/housing is degreasing washed. The Reed switch Reed switch lubrication grease for O-ring and gasket is changed to white vaseline. 170 Courtesy 258-9200-www.stevenengineering.com Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) of Steven

31 176-AMD.qxd 10.5.10 9:36 AM Page 3 Micro Mist Separator Series AMD How to Order AMD650/850 10 650 AMD Body size Made to Order Thread type 650 (“How to Order” and the applicable models are different from 3 ∗ Type Symbol those shown on this page. Be sure to refer to “Made to Order”.) 850 Option Rc Nil Page for details Description Symbol Description Symbol HAA G F Nil Nil — — — HAW 5 NPT N ∗ 1 Drain guide female threaded With differential pressure gauge (GD40-2-01) P.211 X6 4 J With differential pressure switch IN-OUT reversal direction R size Port P.211 AT X37 (With indicator, 125 VAC, 30 VDC) With element service indicator T Accessory Applicable body size 2 ∗ X15 P.212 With IN-OUT flange Size Symbol IDF ∗ 5Dr ain piping and piping for a stop Symbol Description 650 850 With differential pressure gauge valve such as ball valve are IDU X17 P.212 Nil — 1 10 2 ∗ (GD40-2-01) and IN-OUT flange required. 1 ∗ 1 Bracket B 1 14 2 X26 P.213 N.C., N.O. auto drain, drain piping type IDFA ∗ 1B racket is included, 20 2 X12 P.213 White vaseline specifications (but not assembled). ∗ 2 The model with bracket Note) Refer to “How to Order Bowl IDFB is not available for Assembly” on page 206. Auto Drain Specifications/ -X15 and -X17. ID : Available : Not available Option Combinations 3 ∗ Auto drain Auto drain Applicable model Option Symbol Description specifications Auto drain specifications/Option IDG 4 ∗ Nil Drain cock (Without auto drain) R DJ T AMD650 AMD850 N.O. auto drain D N.O. auto drain Auto drain specifications D AMG ∗ Refer to “Auto Drain Specifications/Option Combinations”. 3 1 Drain guide J 4 ∗ 4 Body size 850 is equipped with a ball valve (Rc 3/8 female Option IN-OUT reversal direction R threaded). Mount a piping adapter IDF-AP609 (page 205 ) AFF With element service indicator T to the ball valve if NPT 3/8 female threaded is required. AM 1 AMD801/811/9  Piping support type Free standing type 0  AMD800/810 to 10 AMD 20 20 01 00 AMD AMD 8 8 AMH Body size Body size Port size 8 8 size Port Applicable body size Size Symbol AME 9 9 Applicable body size AMD800, 810 AMD10  0 0  AMD9 Size Symbol 10  1 1 AMD9  AMD8 50(2B)JIS 10K 20 Type 50(2B)JIS 10K AMF FF flange 20 Type Symbol Description FF flange 80(3B)JIS 10K 30 Description Symbol 01 With manual drain cock 80(3B)JIS 10K FF flange 30 SF 00 With manual drain cock With auto drain 11 FF flange 100(4B)JIS 10K 40 With auto drain 10 100(4B)JIS 10K FF flange 40 SFD FF flange 150(6B)JIS 10K 60 FF flange LLB Model Selection Maximum Air Flow Max. flow line AD  Select a model in accordance with the following procedure taking the inlet pressure and the max. air flow rate into consideration. (Example) Inlet pressure: 0.6 MPa 0  GD 3 AMD10 Max. air flow rate: 5 m /min (ANR) 1  . Obtain the intersecting point A of inlet pressure and max. air flow 1 0, 9  AMD9 rate in the graph. The AMD650 is obtained when the max. flow line is above the in- . 2 tersecting point A in the graph. AMD850  , 81  AMD80 Note) Make sure to select a model that has the max. flow line above AMD650 the obtained intersecting point. With a model that has the max. /min (ANR)) 3 AMD550C flow line below the obtained intersecting point, the flow rate will be exceeded, thus leading to a problem such as being unable to satisfy the specifications. AMD450C AMD350C Max. air flow rate (m AMD250C AMD150C Inlet pressure (MPa) 171 Courtesy of Steven Engineering, Inc.-230 258-9200-www.stevenengineering.com Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) Ryan

32 176-AMD.qxd 10.5.10 9:36 AM Page 4 AMD Series Flow Characteristics (Representative values) /Select the model taking the max. flow capacity into consideration. ( Element oil saturation Initial condition) Note) Compressed air over max. flow line in the table below may not meet the specifications of the product.  0/9 AMD150C AMD550C AMD9  1 Max. flow line Max. flow line Pressure drop (MPa) Pressure drop (MPa) Pressure drop (MPa) Max. flow line 3 Air flow rate ( l /min (ANR)) Air flow rate ( l /min (ANR)) Air flow rate (m /min (ANR)) AMD650  AMD250C 0 AMD10 Max. flow line Max. flow line Pressure drop (MPa) Pressure drop (MPa) Pressure drop (MPa) Max. flow line 3 /min (ANR)) l Air flow rate (m /min (ANR)) Air flow rate ( Air flow rate ( /min (ANR)) l  AMD80  AMD350C /81 Max. flow line Max. flow line Pressure drop (MPa) Pressure drop (MPa) 3 l /min (ANR)) /min (ANR)) Air flow rate (m Air flow rate ( AMD450C AMD850 Max. flow line Pressure drop (MPa) Pressure drop (MPa) Max. flow line 3 Air flow rate ( /min (ANR)) Air flow rate (m /min (ANR)) l 172 Courtesy of Steven 258-9200-www.stevenengineering.com Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) Engineering,

33 176-AMD.qxd 10.5.10 9:36 AM Page 5 Micro Mist Separator Series AMD Construction AMD150C to 550C, AMD650 AMD850 q IN OUT IN OUT HAA HAW AT r IDF IDU w IDFA IDFB e ID IDG AMG AFF Component Parts Note Material Description No. AM Note) Refer to “How to Order Bowl Assembly” on page 206. Chrome treated 1 Body Aluminum die-casted ∗ Epoxy coating on inner surface 2 Housing Aluminum die-casted AMD Note) Sight glass is indicated in the figure for easy understanding of 3 — Sight glass Tempered glass component parts. However, it differs from the actual The AMD850 is aluminum casted. ∗ construction. Refer to dimensions on pages 174 through to AMH 177 for details. Replacement Parts AME Model Applicable No. Description Material model AMD550C AMD250C AMD850 AMD350C AMD650 AMD450C AMD150C AMD-EL550 AMD-EL350 AMD-EL650 AMD-EL250 AMD-EL850 AMD-EL150 AMD-EL450 Except option F Element Glass fiber, AMF 4 assembly others AMD-EL350-F AMD-EL550-F AMD-EL150-F AMD-EL250-F AMD-EL450-F — — For option F ∗ Element assembly: With gasket (1 pc.) and O-ring (1 pc.) SF Refer to page 219 for replacement of auto drain. ∗ Element assemblies for Made to Order (X6, X12, X15, X17, X26, X37) are same as those for standard (see the above table). ∗ SFD 0  1/10  0/9  AMD80 /9  /81  LLB AD  GD IN OUT Component Parts/Material Model No. Description AMD800/810/9  1  0  AMD801/811/9 0/10 1 SGP-E, SS400 SGP-E, SS400 Filter case 2 SS400 SGP-E, SS400 Cover Replacement Parts Model No. Material Description AMD801/811 AMD9  0 AMD9 AMD800/810  1 0  AMD10 3 63174 63174 — 63174 3 pcs. 63174 3 pcs. 63174 5 pcs. Element 4 NBR 63148 63148 63148 3 pcs. 63148 3 pcs. 63148 5 pcs. Seal Element O.D112 x I.D90 O.D112 x I.D90 O.D112 x I.D90 — — 5 NBR Seal x T3 x T3 5 pcs. x T3 3 pcs. 6 AL-31S AL-62S AL-63S AL-60S AL-61S V#6500 Gasket Drain JIS B2401G35 JIS B2401G35 JIS B2401G35 JIS B2401G35 JIS B2401G35 7 NBR O-ring 1 pc. 3 pcs. 1 pc. 3 pcs. 5 pcs. 173 Courtesy of Steven Engineering, Inc.-230 258-9200-www.stevenengineering.com Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) Ryan

34 176-AMD.qxd 10.5.10 9:36 AM Page 6 Series AMD Dimensions AMD150C to 550C Auto drain C: With auto drain (N.C.) D: With auto drain (N.O.) P Q S R Drain cock Gray: N.C. 34 Black: N.O. F O ø10 One-touch fitting Combination of D: With auto drain (N.O.) and H: For medium air pressure D Note) I 20 L Bracket T Width across (Accessory) N K flats 17 M 1/4 female threaded U V ø Note) 23 for AMD250C. J Option IN OUT J: Drain guide 1/4 female threaded C H A Width across 20 flats 24 1/4 female threaded S, U: With differential pressure switch (with indicator) Y EB Drain port G Z M5 OUT IN space Maintenance T: With element service indicator W X OUT IN (mm) Element Differential service pressure Bracket related dimensions switch related indicator related Port size Model G C E D B F A dimensions dimensions U J Z K Y X T W S I R Q L P O M N H V 99 176 6 24 23 1.6 10 20 6 4.5 63 26 10 41 12 70 10 54 56 5 6 35 32 63 37 161 1/8, 1/4 AMD150C 5 66 10 66 24 12 80 41 6 28 14 6 40 113 2 6 27 76 37 23 8 36 10 76 193 175 1/4, 3/8 AMD250C 7 80 50 32 34 90 14 37 7 8 7 12 5 23 18 95 41 90 28 42 10 80 2.3 145 225 207 3/8, 1/2 AMD350C 9 106 41 31 23 43 37 106 10 37 166 3.2 10 20 9 50 9 249 90 111 88 18 15 9 55 228 1/2, 3/4 AMD450C 41 122 9 65 100 200 18 60 37 24 281 102 3.2 126 15 9 15 51 122 33 9 10 23 39 10 262 3/4, 1 AMD550C 174 Courtesy of Steven Engineering, Inc.-230 Ryan Way, South 258-9200-www.stevenengineering.com Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) San

35 176-AMD.qxd 10.5.10 9:36 AM Page 7 AMD Series Micro Mist Separator Dimensions AMD650 Auto drain D: With auto drain (N.O.) 180 76 HAA 12 Drain cock: Black HAW 4.5 AT 34 IDF IDU 160 136 ø10 One-touch fitting IDFA IDFB Option J: Drain guide 1/4 female threaded ID IDG 160 150 AMG 20 Bracket 85 (Accessory) 15 11 AFF Width across 20 AM flats 24 40 32 1/4 female OUT IN threaded AMD AMH T: With element service indicator 55 253 AME 337 314 AMF 37 SF OUT IN SFD LLB 10 23 Drain port M5 AD  GD space Maintenance 175 CA Courtesy Engineering, Inc.-230 Ryan Way, South San Francisco, of Steven 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com

36 P0141-P0220-E.qxd 08.11.6 1:51 PM Page 176 AMD Series Dimensions AMD850 Auto drain D: With auto drain (N.O.) 220 for AMD850 110 6 18 23 220 184 3/8 female threaded Option T: With element service indicator Bracket 220 (Accessory) 180 120 24 2 x port size 15 13 OUT IN 30 42 IN OUT 348 461 464 58 Drain Rc 3/8 female 10 threaded space Maintenance 176 258-9200-www.stevenengineering.com of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) Courtesy

37 P0141-P0220-E.qxd 08.11.6 1:51 PM Page 177 Series Micro Mist Separator AMD Dimensions AMD801/811/9  1 HAA HAW OUT OUT IN AT ORIENTATION IDF IDU ≅ IDFA OUT IN IDFB Label ID IDG AMG AFF (mm) Model Connection (Flange) ø D F E J G H C B A ø 270 887 150(6B) 1033 3 760 150 280 400 AMD801/811 AM 50(2B)JIS 10K FF flange 795 520 972 620 300(12B) 1318 300 3 445 AMD9  1 50(2B), 80(3B), 100(4B)JIS 10K FF flange AMD AMH AMD800/810/9 0 0/10   AME AMF SF ORIENTATION SFD OUT IN 3 x ø H holes LLB AD  OUT IN GD Label Drain ≅ (mm) Connection (Flange) Model ø Anchor bolt G F C E D H A B ø l 400 M16 x 1430 1300 20 1520 300 300 500 200(8B) AMD800/810 50(2B), 80(3B)JIS 10K FF flange 24 300 720 1585 560 1320 1480 400 M20 x l 500 AMD9  0 50(2B), 80(3B), 100(4B)JIS 10K FF flange l 500 M20 x 870 745 24 1380 1740 300 1610 550 AMD10  0 100(4B), 150(6B)JIS 10K FF flange 177 Courtesy 258-9200-www.stevenengineering.com Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) of Steven

38 P0141-P0220-E.qxd 08.11.6 1:51 PM Page 178 178 Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San 258-9200-www.stevenengineering.com CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) Francisco,

39 RoHS-AMH.qxd 10.7.26 5:58 PM Page 1 Micro Mist Separator with Pre-filter RoHS AMH Series HAA Model HAW AMH850 AMH150C Model AMH450C AMH350C AMH250C AMH650 AMH550C Can separate and remove aerosol Note) state oil mist in compressed air and AT 200 1000 6000 500 2000 3700 12000 l Rated flow ( /min (ANR)) remove particles such as carbon or IDF dust of more than 0.01 μ m. 1 3 1 1 1 3 3 3 1 1 1 1 11, 12 Por t size , , , , , 4 8 4 2 4 8 4 8 2 , 2 2 IDU Use this product as a pre-filter for compressed air for precision instru- 0.38 2.1 10.5 0.55 0.9 1.4 4.2 Mass (kg) IDFA ments or clean room requiring Note) Max. flow at 0.7 MPa. higher clean air. Max. flow varies depending on the operating pressure. IDFB Refer to “Flow Characteristics” (page 182) and “Maximum Air Flow” below. The conventional pneumatic pres- ID sure line, AM series + AMD series Specifications have been integrated to achieve a IDG reduction in installation space and Compressed air Fluid 1.0 MPa Max. operating pressure in piping labor. 1 ∗ AMG 0.05 MPa Min. operating pressure 1.5 MPa Proof pressure C ° 5 to 60 Ambient and fluid temperature AFF μ m (Filtration efficiency: 99.9%) 0.01 Nominal filtration density Modular connection is possible 3 2 ∗ Max. 0.1 mg/m ( ANR) Oil mist density at outlet AM 3 with AMH150C to 550C. ≈ (Before saturated with oil, less than 0.01 mg/m (ANR) 0.008 ppm) (For details, refer to page 204.) 2 years or when pressure drop reached 0.1 MPa Element life AMD ∗ 1 With auto drain: 0.1 MPa (N.O. type) or 0.15 MPa (N.C. type) 3 (ANR) blown out by compressor. ∗ 2 Oil mist density at 30 mg/m AMH Accessory AME Applicable model AMH650 AMH850 AMH150C AMH250C AMH350C AMH450C AMH550C Bracket assembly AM-BM102 BM57 BM56 AM-BM105 AM-BM101 AM-BM104 AM-BM103 AMF (with 2 mounting screws) SF Model Selection Maximum Air Flow SFD Select a model in accordance with the fol- lowing procedure taking the inlet pressure LLB and the max. air flow rate into consideration. (Example) Inlet pressure: 0.6 MPa 3  AD Max. air flow rate: 5 m /min (ANR) /min (ANR)) 3 1 . Obtain the intersecting point A of inlet pres- AMH650/850 AMH150C to 550C GD sure and max. air flow rate in the graph. 2 The AMH650 is obtained when the max. . flow line is above the intersecting point A Symbol Symbol in the graph. AMH AMH Note) Make sure to select a model that Max. air flow rate (m has the max. flow line above the obtained intersecting point. With a (Auto drain specifications) (Drain cock specifications) model that has the max. flow line Inlet pressure (MPa) below the obtained intersecting point, the flow rate will be excee- ded, thus leading to a problem Made to Order such as being unable to satisfy the (For details, refer to page 210.) specifications. Caution Be sure to read before handling. Refer to front matters 42 and 43 for Safety Instructions and pages 6 to 8 for Air Preparation Equipment Precautions. 179 Courtesy of Steven Engineering, Inc.-230 Ryan Way, South 258-9200-www.stevenengineering.com Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) San

40 176-AMH.qxd 10.5.7 11:10 AM Page 2 Series AMH How to Order AMH150C to 550C AMH 550C 10 Body size Thread type 150C Made to Order Symbol Type (“How to Order” and the applicable models are different from those shown 250C on this page. Be sure to refer to “Made to Order”.) Rc Nil 350C 1 ∗ G F 450C Symbol Description Page for details NPT N — Nil 550C — With differential pressure gauge (GD40-2-01) P.211 X6 1 Conforms to ∗ 3 ∗ ISO1179-1. With IN-OUT flange P.212 X15 With differential pressure gauge (GD40-2-01) size Port P.212 X17 3 ∗ and IN-OUT flange Accessory Applicable body size Symbol Size N.C., N.O. auto drain, drain piping type P.213 X26 Symbol Description 550C 350C 450C 150C 250C 4 ∗ — Nil 1/8 01 Option 2 ∗ Bracket B 1/4 02 Description Symbol 3/8 03 ∗ 2B racket is included, — Nil (but not assembled). 1/2 04 Rubber material: Fluororubber F 3 The model with bracket ∗ 3/4 06 For medium air pressure (1.6 MPa) H is not available for 5 ∗ 1 10 Drain guide 1/4 female threaded J -X15 and -X17. IN-OUT reversal direction R 6, Note) ∗ With differential pressure switch (125 VAC, 30 VDC) S Drain Exhaust Specifications/Option Combinations 6 ∗ With differential pressure switch (30 VDC) U : All types of drain exhaust specifications are available. (including drain guide, With element service indicator T “J” specification) 7 ∗ : N.C. auto drain (“C” specification) is not available. white vaseline Degreasing wash, V : Both N.C. and N.O. auto drain (“C”, “D” specification) are not available. ain piping and piping for a stop valve such as ball valve are required. 5Dr ∗ Nil R V U F S H T ∗ 6 Differential pressure switch is included, (but not assembled). 7 Only body/housing is degreasing washed. ∗ Note Nil Note) Order “U” if conformity to the EU directive is required. F 4 ∗ H Auto drain Note R Symbol Description S Drain cock (Without auto drain) Nil U Note Note N.C. auto drain C T N.O. auto drain D V 4 Refer to “Drain Exhaust Specifications/ ∗ Note: Only one drain exhaust method can be selected. Option Combinations”. : Not available (Only one drain exhaust method can be selected.) Options Symbol F: Rubber material: Fluororubber Symbol J: Drain guide 1/4 female threaded Symbol H: For medium air pressure (1.6 MPa) Can be pipied to the Fluororubber is used for the parts drain exhaust port. Can be used up to 1.6 MPa at such as O-ring and gasket. maximum. 1/4 female threaded Symbol R: IN-OUT reversal direction Symbol S: With differential pressure Symbol U: With differential pressure switch (with indicator) switch (with indicator) Air flow in the separator is changed to Saturation of the Saturation of the right to left. 0.1 0.1 .05 .05 0.15 0.15 0.2 0.2 MPa MPa SMC SMC separator can be separator can be (Air flow direction of the standard: Left observed visually or by observed visually or by to right.) an electrical signal. an electrical signal. (Element life check) (Element life check) Symbol T: With element service indicator ∗ The rated contact voltage is different The rated contact voltage is different ∗ from “S”. from “U”. Saturation of the Max. contact capacity: 10 W DC Max. contact capacity: 10 VA AC, 10 W DC separator can be Rated contact voltage (max. operating Rated contact voltage (max. operating Pressure observed visually. current): 30 V DC (0.33 A) current): 125 V AC (0.08 A), 30 V DC (0.33 A) drop (Element life check) 0.1 MPa Symbol V: Degreasing wash, white vaseline Body/housing is degreasing washed. The Reed switch Reed switch lubrication grease for O-ring and gasket is changed to white vaseline. 180 Courtesy of Steven Engineering, Inc.-230 258-9200-www.stevenengineering.com Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) Ryan

41 176-AMH.qxd 10.5.7 11:10 AM Page 3 Series AMH Micro Mist Separator with Pre-filter How to Order AMH650/850 650 10 AMH Made to Order Body size (“How to Order” and the applicable models are different from those shown on this page. 650 Be sure to refer to “Made to Order”.) 850 HAA Description Page for details Symbol HAW Nil — — Thread type With differential pressure gauge (GD40-2-01) P.211 X6 Symbol Type AT With differential pressure switch (With indicator, 125 VAC, 30 VDC) P.211 X37 Nil Rc 2 ∗ With IN-OUT flange P.212 X15 IDF F G 2 ∗ With differential pressure gauge (GD40-2-01) and IN-OUT flange P.212 X17 IDU NPT N N.C., N.O. auto drain, drain piping type P.213 X26 White vaseline specifications P.213 X12 IDFA size Port 3 Applicable body size ∗ Option Size Symbol IDFB 850 650 Symbol Description 10 1 Nil — ID 1 1 14 2 5 ∗ 1 Drain guide female threaded J 4 20 2 IN-OUT reversal direction R IDG With element service indicator T Accessory ain piping and piping for a stop valve such 5Dr ∗ AMG as ball valve are required. Description Symbol Nil — 1 2 3 ∗ ∗ ∗ Bracket B Auto drain AFF 1B racket is included, ∗ Description Symbol 4 ∗ (but not assembled). Drain cock (Without auto drain) Nil AM ∗ 2 The model with bracket N.O. auto drain D is not available for ∗ 3 Refer to “Auto Drain Specifications/Option -X15 and -X17. AMD Combinations”. ∗ 4 Body size 850 is equipped with a ball valve (Rc3/8 female threaded). Mount a piping AMH adapter IDF-AP609 (page 205) to the ball valve if NPT3/8 female threaded is required. AME AMF Note) Refer to “How to Order Bowl Assembly” on page 206. SF : Available : Not available Auto Drain Specifications/Option Combinations SFD Applicable model Option Auto drain specifications Auto drain specifications/Option DJT AMH650 R AMH850 LLB N.O. auto drain Auto drain specifications D 1 Drain guide J 4  AD Option IN-OUT reversal direction R With element service indicator T GD 181 258-9200-www.stevenengineering.com of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) Courtesy

42 176-AMH.qxd 10.5.7 11:10 AM Page 4 AMH Series /Select the model taking the max. flow capacity into consideration. ( Element oil saturation Initial condition) Flow Characteristics (Representative values) Note) Compressed air over max. flow line in the table below may not meet the specifications of the product. AMH850 AMH150C AMH450C Inlet air pressure Air pressure Inlet air pressure Max. flow line Max. flow line Pressure drop (MPa) Pressure drop (MPa) Pressure drop (MPa) Max. flow line 3 l l /min (ANR)) /min (ANR)) /min (ANR)) Air flow rate ( Air flow rate (m Air flow rate ( AMH250C AMH550C Inlet air pressure Air pressure Max. flow line Pressure drop (MPa) Pressure drop (MPa) Max. flow line Air flow rate ( l l /min (ANR)) Air flow rate ( /min (ANR)) AMH350C AMH650 Inlet air pressure Air pressure Max. flow line Max. flow line Pressure drop (MPa) Pressure drop (MPa) /min (ANR)) l Air flow rate ( /min (ANR)) Air flow rate ( l 182 258-9200-www.stevenengineering.com of Steven Engineering, Inc.-230 Ryan Way, South San Courtesy CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) Francisco,

43 P0141-P0220-E.qxd 08.11.6 1:52 PM Page 183 Series AMH Micro Mist Separator with Pre-filter Construction AMH150C to 550C, AMH650 AMH850 q IN OUT OUT IN HAA HAW AT r IDF IDU w IDFA IDFB e ID IDG AMG AFF AM Component Parts No. Note Material Description Note) Refer to “How to Order Bowl Assembly” on page 206. AMD Chrome treated 1 Body Aluminum die-casted ∗ Epoxy coating on inner surface 2 Housing Aluminum die-casted Note) Sight glass is indicated in the figure for easy understanding of 3 — Sight glass Tempered glass AMH component parts. However, it differs from the actual The AMH850 is aluminum casted. ∗ construction. Refer to dimensions on pages 184 through to 186 for details. AME Replacement Parts Model Applicable No. Description Material AMF model AMH650 AMH350C AMH550C AMH850 AMH150C AMH450C AMH250C AMH-EL550 AMH-EL350 AMH-EL150 AMH-EL650 AMH-EL850 AMH-EL250 AMH-EL450 Except option F Element Glass fiber, 4 SF assembly AMH-EL250-F AMH-EL450-F AMH-EL150-F AMH-EL350-F AMH-EL550-F — — For option F others ∗ Element assembly: With gasket (1 pc.) and O-ring (1 pc.) Refer to page 219 for replacement of auto drain. ∗ SFD ∗ Element assemblies for Made to Order (X6, X12, X15, X17, X20, X26, X37) are same as those for standard (see the above table). LLB AD  GD 183 Courtesy of Steven Engineering, Inc.-230 Ryan 258-9200-www.stevenengineering.com South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) Way,

44 P0141-P0220-E.qxd 08.11.6 1:52 PM Page 184 AMH Series Dimensions AMH150C to 550C Auto drain C: With auto drain (N.C.) D: With auto drain (N.O.) P Q S R Drain cock Gray: N.C. 34 Black: N.O. F O ø10 One-touch fitting Combination of D: With auto drain (N.O.) and H: For medium air pressure D I L Bracket T 20 (Accessory) N K M 1/4 female threaded U V ø J Option IN OUT J: Drain guide 1/4 female threaded C H A 20 1/4 female threaded S, U: With differential pressure switch (with indicator) Y EB Z Drain G M5 OUT IN space Maintenance T: With element service indicator W X IN OUT (mm) Differential Element pressure service Bracket related dimensions indicator related switch related Port size Model C F D E G B A dimensions dimensions Q P O N J V M L U Z T K X W S I R H Y 6 173 1.6 24 4.5 26 63 56 99 10 70 20 37 54 10 5 35 32 20 6 10 63 6 12 41 158 1/8, 1/4 AMH150C 66 6 36 41 6 10 2 8 40 37 20 6 12 24 113 76 80 10 66 76 28 27 190 5 14 172 1/4, 3/8 AMH250C 28 14 42 80 80 20 7 7 95 41 90 10 145 34 32 12 7 37 5 8 18 90 50 2.3 222 204 3/8, 1/2 AMH350C 50 37 111 88 55 166 37 10 15 9 18 43 9 9 106 9 41 10 31 246 3.2 20 90 20 106 225 1/2, 3/4 AMH450C 65 37 100 122 200 9 10 51 10 102 9 278 20 41 3.2 15 15 126 122 24 39 18 9 33 60 259 3/4, 1 AMH550C 184 Courtesy of Steven Engineering, Inc.-230 Ryan Way, South 258-9200-www.stevenengineering.com Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) San

45 P0141-P0220-E.qxd 08.11.6 1:52 PM Page 185 Micro Mist Separator with Pre-filter AMH Series Dimensions AMH650 Auto drain D: With auto drain (N.O.) 180 76 12 HAA Drain cock: Black HAW 4.5 AT 34 136 160 IDF IDU ø10 One-touch fitting IDFA IDFB Option J: Drain guide 1/4 female threaded 160 ID 150 85 20 IDG 15 11 Bracket (Accessory) AMG 40 32 AFF IN OUT 20 AM 1/4 female threaded AMD 253 T: With element service indicator AMH 334 55 311 AME 37 AMF SF OUT IN SFD 20 LLB Drain 10  AD GD space Maintenance 185 Courtesy of Steven Engineering, Inc.-230 Ryan 258-9200-www.stevenengineering.com South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) Way,

46 P0141-P0220-E.qxd 08.11.6 1:52 PM Page 186 AMH Series Dimensions AMH850 Auto drain D: With auto drain (N.O.) 220 for AMH850 110 6 18 23 184 220 3/8 female threaded Option T: With element service indicator Bracket 220 (Accessory) 180 120 24 15 13 OUT IN 30 42 IN OUT 348 461 464 58 Drain 10 Rc 3/8 female threaded space Maintenance 186 258-9200-www.stevenengineering.com of Steven Engineering, Inc.-230 Ryan Way, South San Courtesy CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) Francisco,

47 RoHS-AME.qxd 10.7.26 5:58 PM Page 1 Super Mist Separator RoHS AME Series HAA Model HAW AME850 AME150C Model AME550C AME450C AME250C AME350C AME650 Can separate and adsorb aerosol Note) state fine oil particles in com- AT 200 6000 12000 3700 500 1000 2000 /min (ANR)) Rated flow ( l pressed air and change the oil lubri- IDF 3 1 3 1 3 1 3 1 1 1 1 1 11, 12 Por t size , , , , , 4 4 4 8 4 8 2 8 2 , 2 2 cating compressed air to oilless air IDU or equivalent. 0.8 0.48 2.0 0.3 4.2 1.3 10.5 Mass (kg) IDFA Use this product for filtration of Note) Max. flow at 0.7 MPa. compressed air requiring higher Max. flow varies depending on the operating pressure. IDFB clean air for painting lines, com- Refer to “Flow Characteristics” and “Maximum Air Flow” (page 190). pressed air for clean rooms and/or ID equipment where oils must be avoi- ded. Specifications IDG Compressed air Fluid Indicates the filter element life 1.0 MPa Max. operating pressure AMG by a color change. Accordingly, 0.05 MPa Min. operating pressure the replacement time can be 1.5 MPa Proof pressure AFF judged visually. (A red color spot in- C 5 to 60 ° Ambient and fluid temperature dicates the replacement time.) m (Filtration efficiency: 99.9%) μ 0.01 Nominal filtration rating AM μ m or larger per cubic foot Less than 100 particles of 0.3 Cleanliness at outlet [Less than 35 particles per 10 liters (ANR)] Caution 3 ( ANR) Max. 0.01 mg/m AMD Oil mist density at outlet ( ≈ 0.008 ppm) By all means the “AM” series 1. Element color indicator (Replace the element when a red should be used as a pre-filter. AMH color spot occurred on the surface.) 2. Even if a red color spot does not appear on the surface, the Element life AME Modular connection is possible replacement interval for the element is when the pressure with AME150C to 550C. drop reaches 0.1 MPa or after two years of operation, (For details, refer to page 204.) whichever comes first. AMF SF Accessory SFD Applicable model AME150C AME250C AME350C AME450C AME550C AME650 AME850 Bracket assembly AM-BM105 BM57 BM56 AM-BM101 AM-BM104 AM-BM103 AM-BM102 LLB (with 2 mounting screws) AD  Caution GD Be sure to read before handling. AME150C to 350C AME450C/550C Refer to front matters 42 and 43 for Safety Instructions and pages 6 to 8 for Air Preparation Equipment Precautions. Symbol AME AME650/850 Made to Order (For details, refer to page 210.) 187 Courtesy of Steven Engineering, Inc.-230 Ryan Way, South 258-9200-www.stevenengineering.com Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) San

48 P0141-P0220-E.qxd 08.11.6 1:52 PM Page 188 AME Series How to Order AME150C to 550C AME 550C 10 Option Body size Description Symbol 150C — Nil 250C Rubber material: Fluororubber 350C F For medium air pressure (1.6 MPa) 450C H IN-OUT reversal direction 550C R 3 ∗ white vaseline Degreasing wash, V 3 Only body/housing is degreasing washed. ∗ Thread type Symbol Type Rc Nil Accessory 1 ∗ G F Description Symbol NPT N — Nil ∗ 1 Conforms to 2 ∗ Bracket B ISO1179-1. ∗ 2 Bracket is included, (but not assembled). Port size Applicable body size Size Symbol 250C 350C 450C 550C 150C 1/8 01 1/4 02 3/8 03 1/2 04 3/4 06 1 10 Options Symbol H: For medium air pressure Symbol F: Rubber material: Fluororubber Symbol R: IN-OUT reversal direction (1.6 MPa) Air flow in the separator is changed to Fluororubber is used for the parts right to left. Can be used up to 1.6 MPa at such as O-ring and gasket. (Air flow direction of the standard: Left maximum. to right.) Symbol V: Degreasing wash, white vaseline Body/housing is degreasing washed. The lubrication grease for O-ring and gasket is changed to white vaseline. 188 Courtesy 258-9200-www.stevenengineering.com Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) of Steven

49 P0141-P0220-E.qxd 08.11.6 1:52 PM Page 189 AME Series Super Mist Separator How to Order AME650/850 650 10 AME Body size Made to Order (“How to Order” and the applicable models are different 650 from those shown on this page. Be sure to refer to the page 850 “Made to Order”.) HAA Page for details Description Symbol HAW — Nil — White vaseline specifications P.213 X12 AT Thread type IDF Type Symbol IDU Nil Rc Option F G Description Symbol IDFA NPT N Nil — IN-OUT reversal direction R IDFB Port size Applicable body size ID Symbol Size Accessory 650 850 Symbol Description 1 10 IDG — Nil 1 1 14 2 ∗ Bracket B 2 20 AMG ∗ Bracket is included, (but not assembled). AFF AM Note) Refer to “How to Order Bowl Assembly” on page 206. AMD AMH AME AMF SF SFD LLB  AD GD 189 CA Courtesy Engineering, Inc.-230 Ryan Way, South San Francisco, of Steven 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com

50 176-AME.qxd 10.5.7 11:11 AM Page 1 Series AME (Element initial condition) Flow Characteristics (Representative values) Note) Compressed air over max. flow line in the table below may not meet the specifications of the product. AME450C AME650 AME150C Max. flow line Max. flow line Max. flow line Pressure drop (MPa) Pressure drop (MPa) Pressure drop (MPa) l Air flow rate ( /min (ANR)) l Air flow rate ( /min (ANR)) l /min (ANR)) Air flow rate ( AME850 AME550C AME250C Max. flow line Max. flow line Max. flow line Pressure drop (MPa) Pressure drop (MPa) Pressure drop (MPa) 3 /min (ANR)) Air flow rate ( l /min (ANR)) /min (ANR)) Air flow rate (m Air flow rate ( l AME350C Max. flow line Maximum Air Flow Pressure drop (MPa) /min (ANR)) Air flow rate ( l /min (ANR)) 3 Model Selection Select a model in accordance with the following procedure taking the inlet pressure and the max. air flow rate into consideration. (Example) Inlet pressure: 0.6 MPa 3 Max. air flow rate: 5 m /min (ANR) Max. air flow rate (m . Obtain the intersecting point A of inlet pressure and max. air flow 1 rate in the graph. . 2 The AME650 is obtained when the max. flow line is above the in- tersecting point A in the graph. Note) Make sure to select a model that has the max. flow line above the obtained intersecting point. With a model that has the max. flow line below the obtained intersecting point, the flow rate will be exceeded, thus leading to a problem such as being unable to satisfy the specifications. Inlet pressure (MPa) 190 Courtesy of Steven Engineering, Inc.-230 Ryan 258-9200-www.stevenengineering.com South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) Way,

51 P0141-P0220-E.qxd 08.11.6 1:52 PM Page 191 AME Series Super Mist Separator Construction AME650/850 AME150C to 550C q IN OUT OUT IN HAA HAW AT IDF IDU IDFA r IDFB ID IDG e AMG w AFF Component Parts AM Note) Refer to “How to Order Bowl Assembly” on page 206. No. Material Note Description Chrome treated 1 Body Aluminum die-casted AMD Note) Sight glass is indicated in the figure for easy understanding of ∗ Epoxy coating on inner surface 2 Housing Aluminum die-casted component parts. However, it differs from the actual — 3 Sight glass Tempered glass construction. Refer to dimensions on pages 192 through to AMH ∗ The AME850 is aluminum casted. 194 for details. AME Replacement Parts Model Applicable No. Description Material model AME250C AME450C AME350C AME650 AME150C AME850 AME550C AMF AME-EL450 AME-EL850 AME-EL350 AME-EL650 AME-EL250 AME-EL550 AME-EL150 Except option F Element Glass fiber, 4 assembly others AME-EL250-F AME-EL350-F AME-EL550-F AME-EL150-F AME-EL450-F — — For option F SF Element assembly: With gasket (1 pc.) and O-ring (1 pc.) ∗ ∗ Element assemblies for Made to Order (X12, X20) are same as those for standard (see the above table). SFD LLB  AD GD 191 Courtesy of Steven Engineering, 258-9200-www.stevenengineering.com Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) Inc.-230

52 176-AME.qxd 10.5.7 11:11 AM Page 2 AME Series Dimensions AME150C to 350C P Q T S F R E D N Bracket LU (Accessory) O K M V W ø J B IN OUT C I A G space Maintenance (mm) Bracket related dimensions Port size Model A B C D E G F O W M T L V U S K R N Q I P J 1/8, 1/4 83 10 99 56 20 63 5 6 6 54 12 6 10 10 63 4.5 70 35 26 7.5 54 1.6 AME150C 1/4, 3/8 103 14 6 10 121 8 40 10 6 80 73 66 28 6 76 66 5 12 5 24 76 2 AME250C 3/8, 1/2 132 8 95 14 18 98 34 10 7 150 80 7 90 12 5 28 90 7 2.3 50 5 80 AME350C 192 Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San 258-9200-www.stevenengineering.com CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) Francisco,

53 P0141-P0220-E.qxd 08.11.6 1:52 PM Page 193 Super Mist Separator Series AME Dimensions AME450C/550C P D Q T HAA HAW AT IDF IDU R IDFA IDFB ID E IDG D AMG N F AFF L U Bracket O (Accessory) AM V M W ø AMD JK B AMH OUT IN AME C AMF I A SF SFD LLB AD  G GD H space Maintenance (mm) Bracket related dimensions Port size Model A B G H F D C E U W I O J P V Q K R L T N M 151 1/2, 3/4 36 111 55 15 9 18 9 9 10 31 90 88 10 106 3 106 105 20 3.2 50 172 AME450C 187 3/4, 1 10 122 65 122 206 126 130 9 60 9 100 102 15 18 3.2 3 33 9 24 44 15 AME550C 193 Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San 258-9200-www.stevenengineering.com CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) Francisco,

54 P0141-P0220-E.qxd 08.11.6 1:52 PM Page 194 Series AME Dimensions AME650/850 Bracket (Accessory) 2 x port size IN OUT space Maintenance (mm) Bracket related dimensions Port size Model B E A C F G D H M P J S K L R I O Q N 1 1 1, 11 160 291 15 136 10 20 167 — 66 32 76 150 314 4.5 160 85 180 40 AME650 2 1 1 13 42 15 184 30 406 6 96 180 10 403 220 120 110 220 24 — 220 235 AME850 2 , 2 194 Courtesy of Steven Engineering, Inc.-230 Ryan Way, 258-9200-www.stevenengineering.com San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) South

55 RoHS-AMF.qxd 10.7.26 5:59 PM Page 1 Odor Removal Filter RoHS AMF Series HAA Model HAW AMF650 AMF450C AMF350C AMF250C AMF850 AMF550C AMF150C Model Efficiently can remove odor in com- Note) pressed air with an activated carbon AT 500 1000 2000 3700 12000 6000 200 l /min (ANR)) Rated flow ( element. The unit is designed for IDF use in the area such as a clean room 3 1 3 3 1 3 1 1 1 1 1 1 12 11, size Por t , , , , , 8 8 2 2 4 4 4 4 8 , 2 2 IDU where odors must be avoided. Mass (kg) 0.3 0.48 0.8 1.3 2.0 4.2 10.5 IDFA Can remove odor and gas ingre- dients in compressed air. Note) Max. flow at 0.7 MPa. Max. flow varies depending on the operating pressure. Activated carbon element with large IDFB Refer to “Flow Characteristics” (page 198) and “Maximum Air Flow” (page 197). filtration area. Easy replacement of elements. ID Model/Free Standing Type IDG Modular connection is possible Model AMF800 AMF1000 AMF900 /min (ANR)) l Rated flow ( 8000 24000 40000 with AMF150C to 550C. 100 (4B),150 (6B) JIS 50 (2B), 80 (3B),100 (4B) JIS 50 (2B) JIS AMG (For details, refer to page 204.) size Por t 10K FF flange 10K FF flange 10K FF flange Mass (kg) 200 410 90 AFF AM Model/Piping Support Type AMF801 Model AMF901 AMD Rated flow ( /min (ANR)) l 8000 24000 Por t size 50 (2B) JIS 10K FF flange 50 (2B), 80 (3B),100 (4B) JIS 10K FF flange AMH Mass (kg) 40 120 AME Specifications Compressed air Fluid AMF 1.0 MPa Max. operating pressure AMF150C to 350C AMF450C/550C 0.05 MPa Min. operating pressure SF 1.5 MPa Proof pressure 5 to 60 ° C Ambient and fluid temperature SFD μ 0.01 m (Filtration efficiency: 99.9%) Nominal filtration rating Less than 100 particles of 0.3 μ m or larger per cubic foot [Less than 35 particles per 10 liters (ANR)] Cleanliness at outlet LLB (The “AME” series is required on the inlet side.) 3 (ANR) ( ≈ 0.0032 ppm) Max. 0.004 mg/m AD  Oil mist density at outlet (The “AME” series is required on the inlet side.) 1. Replace the element when you smell oil on the outlet side. GD 2. Even if the deodorization performance is normal, the Element life replacement interval for the element is when the pressure drop reaches 0.1 MPa or after two years of operation, whichever comes first. AMF650/850 Accessory (Option) Applicable model AMF150C AMF250C AMF350C AMF450C AMF550C AMF650 AMF850 Symbol Bracket assembly AMF BM56 AM-BM105 BM57 AM-BM103 AM-BM102 AM-BM104 AM-BM101 (with 2 mounting screws) Caution Made to Order (For details, refer to page 210.) Be sure to read before handling. Refer to front matters 42 and 43 for Safety Instructions and pages 6 to 8 for Air Preparation Equipment Precautions. 195 258-9200-www.stevenengineering.com of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) Courtesy

56 P0141-P0220-E.qxd 08.11.6 1:52 PM Page 196 AMF Series How to Order AMF150C to 550C 10 AMF 550C Option Body size Description Symbol 150C — Nil 250C Rubber material: Fluororubber 350C F For medium air pressure (1.6 MPa) 450C H IN-OUT reversal direction 550C R 3 white vaseline Degreasing wash, V 3 Only body/housing is degreasing washed. Thread type Symbol Type Rc Nil Accessory 1 G F Symbol Description NPT N — Nil 1 Conforms to 2 Bracket B ISO1179-1. 2 Bracket is included, (but not assembled). Port size Applicable body size Symbol Size 450C 550C 150C 250C 350C 1/8 01 1/4 02 3/8 03 1/2 04 3/4 06 1 10 Options Symbol H: For medium air pressure Symbol F: Rubber material: Fluororubber Symbol R: IN-OUT reversal direction (1.6 MPa) Air flow in the separator is changed to Fluororubber is used for the parts right to left. Can be used up to 1.6 MPa at such as O-ring and gasket. (Air flow direction of the standard: Left maximum. to right.) Symbol V: Degreasing wash, white vaseline Body/housing is degreasing washed. The lubrication grease for O-ring and gasket is changed to white vaseline. 196 Courtesy of Steven Engineering, Inc.-230 Ryan Way, South 258-9200-www.stevenengineering.com Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) San

57 P0141-P0220-E.qxd 08.11.6 1:52 PM Page 197 Series AMF Odor Removal Filter How to Order AMF650/850 10 650 AMF Made to Order Body size (“How to Order” and the applicable models are different 650 from those shown on this page. Be sure to refer to “Made 850 to Order”.) HAA Description Symbol Page for details HAW Thread type Nil — — Type Symbol White vaseline specifications X12 AT P.213 Nil Rc IDF F G Option IDU NPT N Symbol Description Nil — IDFA Port size IN-OUT reversal direction R Applicable body size IDFB Size Symbol 850 650 Accessory 1 10 Description Symbol ID 1 1 14 2 Note) Refer to “How to Order Bowl Assembly” — Nil ∗ 20 2 on page 206. Bracket B IDG Bracket is included, ∗ (but not assembled). AMG Piping support type Free standing type AMF801/901 AMF800 to 1000 AFF 80AMF 80AMF 20 20 0 1 AM Body size Body size AMD 80 80 90 90 Vessel shape AMH 100 Vessel shape Piping support type Free standing type AME Port size Port size Applicable body size Applicable body size AMF Size Size Symbol Symbol 800 900 1000 901 801 20 50 (2B) JIS 10K FF flange 50 (2B) JIS 10K FF flange 20 SF 30 80 (3B) JIS 10K FF flange 80 (3B) JIS 10K FF flange 30 100 (4B) JIS 10K FF flange 40 100 (4B) JIS 10K FF flange 40 60 150 (6B) JIS 10K FF flange SFD LLB Model Selection Maximum Air Flow  AD Select a model in accordance with the following procedure taking the inlet pressure and the max. air flow rate into consideration. GD (Example) Inlet pressure: 0.6 MPa 3 Max. air flow rate: 5 m /min (ANR) . Obtain the intersecting point A of inlet pressure and max. air flow 1 rate in the graph. 2 . The AMF650 is obtained when the max. flow line is above the in- tersecting point A in the graph. Note) Make sure to select a model that has the max. flow line above /min (ANR)) the obtained intersecting point. With a model that has the max. 3 flow line below the obtained intersecting point, the flow rate will be exceeded, thus leading to a problem such as being unable to satisfy the specifications. Max. air flow rate (m Inlet pressure (MPa) 197 Courtesy of Steven 258-9200-www.stevenengineering.com Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) Engineering,

58 176-AMF.qxd 10.5.7 11:10 AM Page 1 Series AMF Flow Characteristics /Refer to “Model Selection” on page 197. (Element initial condition) (Representative values) Note) Compressed air over max. flow line in the table below may not meet the specifications of the product. AMF900/901 AMF550C AMF150C Max. flow line Pressure drop (MPa) Pressure drop (MPa) Pressure drop (MPa) 3 /min (ANR)) l /min (ANR)) Air flow rate ( l Air flow rate ( Air flow rate (m /min (ANR)) AMF650 AMF250C AMF1000 Max. flow line Max. flow line Pressure drop (MPa) Pressure drop (MPa) Pressure drop (MPa) 3 /min (ANR)) Air flow rate ( l /min (ANR)) l Air flow rate ( /min (ANR)) Air flow rate (m AMF350C AMF800/801 Pressure drop (MPa) Pressure drop (MPa) Max. flow line 3 Air flow rate ( l /min (ANR)) Air flow rate (m /min (ANR)) AMF450C AMF850 Max. flow line Max. flow line Pressure drop (MPa) Pressure drop (MPa) 3 /min (ANR)) Air flow rate (m l /min (ANR)) Air flow rate ( 198 Courtesy of Steven Engineering, Inc.-230 Ryan 258-9200-www.stevenengineering.com South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) Way,

59 P0141-P0220-E.qxd 08.11.6 1:52 PM Page 199 Odor Removal Filter AMF Series Construction AMF650/850 AMF150C to 550C q OUT IN OUT IN HAA HAW AT IDF IDU IDFA r IDFB ID IDG AMG e w AFF AM Component Parts Note) Refer to “How to Order Bowl Assembly” on page 206. No. Material Note Description AMD Chrome treated 1 Body Aluminum die-casted Note) Sight glass is indicated in the figure for easy understanding of ∗ Epoxy coating on inner surface 2 Housing Aluminum die-casted component parts. However, it differs from the actual AMH — 3 Sight glass Tempered glass construction. Refer to dimensions on pages 200 to 203 for details. ∗ The AMF850 is aluminum casted. AME Replacement Parts Model Applicable No. Description Material AMF model AMF850 AMF650 AMF250C AMF450C AMF150C AMF550C AMF350C AMF-EL450 AMF-EL350 AMF-EL550 AMF-EL650 AMF-EL250 AMF-EL850 AMF-EL150 Except option F Element Glass fiber, 4 assembly SF AMF-EL250-F AMF-EL150-F AMF-EL450-F AMF-EL350-F AMF-EL550-F — — For option F others Element assembly: With gasket (1 pc.) and O-ring (1 pc.) ∗ Element assemblies for Made to Order (X12, X20) are same as those for standard (see the above table). ∗ SFD  AMF80 /90  /1000 LLB N-4 AD  N-5 Pressure Pressure outlet outlet (OUT side) GD (IN side) IN OUT N-2 N-1 Component Parts/Material Model No. Description AMF801/901 AMF800/900/1000 1 SGP-E: SS400 SGP-E: SS400 Filter case Element 2 SS400 SGP-E: SS400 Cover Replacement Parts Model No. Description Material AMF1000 AMF801 AMF900 AMF901 AMF800 3 63271 63271 — 63271 3 pcs. 63271 3 pcs. 63271 5 pcs. Element 4 NBR 63148 63148 63148 3 pcs. 63148 3 pcs. 63148 5 pcs. Seal O.D112 x I.D90 O.D112 x I.D90 O.D112 x I.D90 Drain 5 NBR Seal — — x T3 1 pc. x T3 5 pcs. x T3 3 pcs. N-3 AL-63S AL-61S AL-60S 6 AL-62S V#6500 AL-31S Gasket 3 pcs. JIS B2401G35 JIS B2401G35 JIS B2401G35 JIS B2401G35 JIS B2401G35 7 NBR O-ring 1 pc. 1 pc. 3 pcs. 3 pcs. 5 pcs. 199 Courtesy of Steven Engineering, Inc.-230 Ryan Way, 258-9200-www.stevenengineering.com San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) South

60 176-AMF.qxd 10.5.7 11:10 AM Page 2 Series AMF Dimensions AMF150C to 350C P Q T S F R E D N Bracket LU (Accessory) O K M V W ø J B IN OUT C I A G space Maintenance (mm) Bracket related dimensions Port size Model A C D E F G B I N P J S K U R V L M Q W O T 5 54 99 6 1.6 10 7.5 6 26 56 12 54 4.5 6 10 20 10 70 63 35 63 1/8, 1/4 83 AMF150C 121 6 28 6 8 66 24 66 5 14 10 2 10 73 40 76 80 76 5 6 12 1/4, 3/8 103 AMF250C 80 10 18 12 5 7 28 7 2.3 50 90 150 98 95 14 8 5 34 90 7 80 3/8, 1/2 132 AMF350C 200 Courtesy of Steven Engineering, Inc.-230 Ryan Way, South 258-9200-www.stevenengineering.com Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) San

61 P0141-P0220-E.qxd 08.11.6 1:52 PM Page 201 AMF Series Odor Removal Filter Dimensions AMF450C/550C P D Q T HAA HAW AT IDF IDU R IDFA IDFB ID E IDG D AMG N F AFF L U Bracket O (Accessory) AM V M W ø AMD JK B AMH IN OUT AME C AMF I A SF SFD LLB  AD G GD H space Maintenance (mm) Bracket related dimensions Model Port size A D H C F E B G L J U M N W V K I O T R P Q 50 31 55 3.2 15 9 18 9 9 10 88 90 172 36 10 111 106 3 106 105 20 151 1/2, 3/4 AMF450C 122 100 102 206 18 44 60 15 9 65 9 3 3.2 122 10 130 15 24 126 33 9 187 3/4, 1 AMF550C 201 Courtesy of Steven Engineering, Inc.-230 Ryan Way, South 258-9200-www.stevenengineering.com Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) San

62 P0141-P0220-E.qxd 08.11.6 1:52 PM Page 202 Series AMF Dimensions AMF650/850 Bracket (Accessory) 2 x port size IN OUT space Maintenance (mm) Bracket related dimensions Port size Model D A B G C H EF P L S N J O R M K Q I 1 1 1, — 10 150 40 167 85 136 15 180 66 160 76 20 32 291 314 11 4.5 160 AMF650 2 1 1 — 180 13 24 15 30 406 96 10 220 6 220 403 235 110 220 184 120 42 AMF850 2 , 2 202 Courtesy of Steven Engineering, Inc.-230 Ryan Way, 258-9200-www.stevenengineering.com San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) South

63 P0141-P0220-E.qxd 08.11.6 1:52 PM Page 203 Odor Removal Filter Series AMF Dimensions AMF801/901 HAA HAW OUT IN ORIENTATION AT IDF IDU ≈ IDFA OUT IN IDFB Label ID IDG AMG AFF (mm) Model Connection (Flange) ø E G B F H C A D ø J 550 797 150 (6B) 270 823 150 3 400 280 AM 50 (2B) JIS 10K FF flange AMF801 300 867 3 1093 520 620 570 300 (12B) 445 AMF901 50 (2B), 80 (3B), 100 (4B) JIS 10K FF flange AMD AMH AMF800/900/1000 AME AMF ORIENTATION SF IN OUT SFD 3 x ø H holes LLB  AD OUT IN GD Label Drain ≈ (mm) Model Connection (Flange) Anchor bolt ø F B H E C D G A ø M16 x 400 l 1200 20 1070 1290 300 330 500 50 (2B) JIS 10K FF flange AMF800 200(8B) M20 x l 500 400 300 560 720 24 1070 1335 1230 50 (2B), 80 (3B), 100 (4B) JIS 10K FF flange AMF900 870 M20 x l 500 1450 1320 1090 300 550 745 24 AMF1000 100 (4B), 150 (6B) JIS 10K FF flange 203 Courtesy of Steven Engineering, Inc.-230 258-9200-www.stevenengineering.com Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) Ryan

64 176-AMF.qxd 10.5.7 11:10 AM Page 3 Optional Accessories Spacer for Modular Connection Select a spacer from those listed below when combining modular type AFF2C to  150C to 550C. The spacer must be ordered separately. 22C, AM (Note: Spacer with bracket (Y200T to Y600T) cannot be used.) Caution Modular connection Mount the attached bracket on one side when connecting 2 sets. Mount the attached brackets on both sides when connecting 3 sets or more. As a guideline for the number of brackets, one bracket should be mounted for every 2 products. Combination examples of modular applicable products Arrangement example Arrangement example B 1 pc.   AMH250C- AMH250C- B 1 pc. 1 pc. AME250C 1 pc. AME250C Y300 Spacer: 1 pc.  1 pc. Y300 AMF250C- B Bracket 2 pcs. Y300 240 158 193 193 175 175 AME250C B AMF250C  AME250C 156 236 B  AMH250C AMH250C  B Spacer D Center of IN/OUT ports C 1 X-X B X RELEASE 2 Y200 Y400 X Model Model ABCD Seal 48 18.5 35.5 3  AFF2C, AM 150C Y200 59 26 47 4 Y300 AFF4C, AM 250C  65 31 57 5 Y400 AFF8C, AM  350C A 75 33 61 5 AFF11C, AM 450C Y500  (Spacer width) 86 41 75.5 6 550C  AFF22C, AM Y600 Replacement Parts Part no. Description Material Y200 Y600 Y300 Y500 Y400 Y200P-061S Y400P-060S Y600P-060S Y500P-060S Y300P-060S Seal HNBR 204 Courtesy 258-9200-www.stevenengineering.com Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) of Steven

65 P0141-P0220-E.qxd 08.11.6 1:52 PM Page 205 Optional Accessory Piping Adapter E (Width across flats) Female thread side B HAA HAW AT Male thread side A IDF D Dimensions (mm) IDU Thread type and port size C DE Material C Part no. Female thread Male thread IDFA side side A B R 3/8 IDF-AP609 NPT 3/8 22 15 30 Brass IDFB ID IDG AMG AFF AM AMD AMH AME AMF SF SFD LLB  AD GD 205 Courtesy of Steven 258-9200-www.stevenengineering.com Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) Engineering,

66 RoHS-AMF.qxd 10.7.26 5:59 PM Page 2 Bowl Assembly  /AM  AFF-CA -CA  RoHS Bowl Assembly series can be replaced without removing the main body from piping if the drain exhaust specification is to be Bowl assembly for the AFF and AM  changed from the drain cock type to the auto drain type or if the bowl has been damaged. How to Order Bowl Assembly  AFF2C to 22C, AM, AMD, AMH, AMG150C to 550C CA AM Option Symbol Description Body size — Nil 150C Rubber material: Fluororubber F 250C For medium air pressure (1.6 MPa) H 350C V Degreasing wash, white vaseline 450C 550C Note 2) Thread type Symbol Type Drain exhaust Rc Nil Symbol Description Note 3) F G With drain cock A N NPT C With N.C. auto drain Note 2) Corresponded to the drain exhaust D With N.O. auto drain symbol C, D and J. Select according to Note 1) J With drain guide the body thread type. Note 1) Drain piping and piping for a Note 3) Not corresponded to the drain exhaust stop valve such as a ball symbol C and D. valve are required. Select no symbol when the body thread Auto Drain Specifications/ symbol is F. Option Combinations : Not available : Available Applicable Model : Plural options cannot be selected. (i.e. Combinations such as C-FV, D-FHV are not Applicable model Bowl assembly model possible.) AM-CA150C AFF2C, AM150C, AMD150C, AMH150C, AMG150C Symbol H V F AM-CA250C AFF4C, AM250C, AMD250C, AMH250C, AMG250C A AM-CA350C AFF8C, AM350C, AMD350C, AMH350C, AMG350C C AM-CA450C AFF11C, AM450C, AMD450C, AMH450C, AMG450C D AM-CA550C AFF22C, AM550C, AMD550C, AMH550C, AMG550C J  AFF37B/75B CA 37B AFF Note 3) Body size Thread type 37B Type Symbol 75B Rc Nil Note 4) F G N NPT Note 3) Corresponded to the drain exhaust symbol D and J. Drain exhaust Select according to the body thread type. Description Symbol Note 4) Not corresponded to the drain exhaust symbol C and D. Note 1) A With drain cock Select no symbol when the body thread symbol is F. With N.O. auto drain D Note 2) J With drain guide Note 1) Body size 75B is equipped with a ball valve (Rc 3/8 female threaded). Mount a piping adapter IDF-AP609 (page 205) to the ball valve if NPT 3/8 female threaded is required. Note 2) Drain piping and piping for a stop valve such as a ball valve are required. For body size 75B, substitute with a ball valve. (symbol: A) 206 Courtesy of Steven Engineering, Inc.-230 Ryan 258-9200-www.stevenengineering.com South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) Way,

67 P0141-P0220-E.qxd 08.11.6 1:52 PM Page 207 Bowl Assembly AFF-CA  /AM  -CA  How to Order Bowl Assembly  Series AM, AMD, AMH, AMG 650CA AM AMD Note 3) Thread type Symbol Type AMH Nil Rc HAA F G AMG HAW N NPT Body size Note 3) Corresponded to the drain exhaust AT 650 symbol D and J. Select according to 850 the body thread type. IDF IDU Drain exhaust IDFA Symbol Description Note 1) A With drain cock With N.O. auto drain D IDFB Note 2) J With drain guide Note 1) Body size 850 is equipped with a ball valve ID (Rc 3/8 female threaded). Mount a piping adapter IDF-AP609 (page 205) to the ball valve if NPT 3/8 female threaded is required. IDG Note 2) Drain piping and piping for a stop valve such as a ball valve are required. AMG For body size 850, substitute with a ball valve. (symbol: A) AFF AM  AME, AMF150C to 550C AMD A CA AME AMH Note) Option Body size AME 150C Description Symbol 250C Nil — 350C Rubber material: Fluororubber F AMF 450C H For medium air pressure (1.6 MPa) 550C V Degreasing wash, white vaseline SF Note) Combination of F and H is not available. SFD Applicable Model Bowl assembly model Applicable model LLB AME-CA150C AME150C, AMF150C AME-CA250C AME250C, AMF250C AME-CA350C AME350C, AMF350C AD  AME-CA450C AME450C, AMF450C AME-CA550C AME550C, AMF550C GD AME, AMF650/850  A 650CA AME AMF Body size 650 850 207 Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San 258-9200-www.stevenengineering.com CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) Francisco,

68 176-AMF.qxd 10.5.7 11:10 AM Page 4 -CA AFF-CA  /AM   Dimensions: Series AFF, AM, AMD, AMH, AMG  150C to 550C, AM  650 Size: AFF2C to 22C, AFF37B, AM (B) (B) (B) (B) Note 1) Note 1) Note 1) (A) (A) (A) (C) 20 20 23 34 M5 female 1/4 female threaded 1/4 female threaded threaded Drain port Note 2) For Rc, G: ø10 Drain port Drain port For NPT: 3/8 Drain port Auto drain for Drain guide Drain cock medium air pressure Auto drain (mm) Series AFF Series AM, AMD, AMG, AMH C B A Size Size Note 1) Model no. labels are not affixed to the AM-CA150C to 550C. 150C 148 137 63 2C Note 2) Select according to the body thread type. 250C 142 76 153 4C Applicable tubing size for One-touch fitting 350C 165 176 90 8C Rc, G: ø10 450C 192 181 106 11C NPT: ø3/8 inch 550C 216 205 122 22C 37B 650 160 248 259 Size: AFF75B, AM 850  (220) (220) 266 266 (344) (379) 23 (58) 3/8 female threaded Drain port Rc 3/8 Drain port 208 Courtesy of Steven Engineering, Inc.-230 Ryan Way, South 258-9200-www.stevenengineering.com Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) San

69 P0141-P0220-E.qxd 08.11.6 1:52 PM Page 209 /AM  -CA   AFF-CA Bowl Assembly Dimensions: Series AME, AMF AME150C to 550C, AMF150C to 550C  (B) HAA HAW AT (A) IDF IDU IDFA IDFB (mm) ID Series AME, AMF B A Size IDG 63 60 150 250 76 70 AMG 350 90 90 450 106 104 AFF 550 122 130 AM  AME650/850, AMF650/850 AMD AMH (B) AME AMF SF SFD (A) LLB  AD GD (mm) Series AME, AMF A B Size 225 160 650 850 319 120 209 CA Courtesy Engineering, Inc.-230 Ryan Way, South San Francisco, of Steven 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com

70 P0141-P0220-E.qxd 08.11.6 1:52 PM Page 210 Compressed Air Cleaning Filter Series Made to Order/Special Specifications Please consult with SMC for detailed specifications, size and delivery. Made to Order Applicable model Reference Symbol Contents page AMF AMG AMH AMD AM AME AFF 1. With Differential Pressure Gauge X6 (GD40-2-01) P.211 2. With Differential Pressure Switch X37 (With Indicator) 3. With IN-OUT Flange X15 P.212 4. With Pressure Differential Gauge X17 (GD40-2-01), IN-OUT Flange 5. N.C., N.O. Auto Drain, Drain Piping Type X26 P.213 6. White Vaseline Specifications X12 P.214 7. Mist Separator for High Flow Rate (0.3 μ m) X13 Special Specifications Applicable model Reference Contents page AFF AMG AMF AME AMD AM AMH Clean Series (10-Series) P.215 Copper-free, Fluorine-free (20-Series) 210 258-9200-www.stevenengineering.com of Steven Engineering, Inc.-230 Ryan Way, South San Courtesy CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) Francisco,

71 176-AMF.qxd 10.5.7 11:10 AM Page 5 Compressed Air Cleaning Filter Series Made to Order Specifications 1 Please consult with SMC for detailed specifications, size and delivery. 2. With Differential Pressure Switch 1. With Differential Pressure Gauge (GD40-2-01) (With indicator) (125 VAC, 30 VDC) A differential pressure gauge that keeps track of the filter life is instal- led on the filter itself. This facilitates piping and achieves a compact Allows visual confirmation of differential pressure which indicates the design. element life. The built-in contact enables remote control. ∗ Place an order separately if conformity to the EU directive is required. Specifications Specifications AFF2C to 22C, 37B, 75B Applicable model HAA HAW Applicable model AFF37B, 75B ∗ Refer to “How to Order” for standard specifications. Refer to “How to Order” for standard ∗ How to Order AT specifications. How to Order IDF X6 AFF IDU X37 AFF ∗ Body size ∗ IDFA Option ∗ ∗ Body size Thread type (Not applicable with ∗ Option F, H, S, T, U, V) ∗ ∗ (Not applicable with T) size Port Thread type IDFB ∗ ∗ Auto drain Accessory ∗ ∗ Accessory size Port ID Specifications Specifications Applicable AM150C to 550C, 650, 850, AMD150C to 550C, 650, 850, AM650, 850, AMD650, 850, IDG Applicable model model AMH150C to 550C, 650, 850 AMH650, 850 Refer to “How to Order” for standard ∗ Refer to “How to Order” for standard ∗ AMG specifications. How to Order specifications. How to Order AFF X6 AM X37 AM AM AMD ∗ AMD Option ∗ Option (Not applicable with (Not applicable with T) AMD AMH AMH F, H, S, T, U, V) ∗ ∗ Accessory ∗ Auto drain Body size ∗ Body size AMH ∗ ∗ Accessory ∗ Port size Thread type ∗ Thread type ∗ size Port AME Note) • The AMG series is not applicable since water drops could Note) • The AMG series is not applicable since water drops could ingress inside its differential pressure gauge, resulting in ingress inside its differential pressure gauge, resulting in AMF malfunction or damage to the product. malfunction or damage to the product. • Cannot be mounted to the AME and AMF series. (It • Cannot be mounted to the AME and AMF series. (It affects the cleanliness at the outlet.) affects the cleanliness at the outlet.) SF SFD Dimensions Dimensions 60 LLB (500) 45 (41) AD  B 0.1 0.15 .05 0.2 MPa SMC GD IN OUT OUT IN A A Drain port Drain port (mm) (mm) Series AM, AMD, AMH Series AM, AMD, AMH Series AFF Series AFF A AB size Por t size Por t Size Size Size Size 1 355 242 80 650 37B 150C 2C 1/8, 1/4 1, 1 2 1 501 80 255 75B 850 250C 4C 1/4, 3/8 1 , 2 2 80 287 3/8, 1/2 8C 350C 308 80 1/2, 3/4 450C 11C 342 80 3/4, 1 550C 22C 1 80 394 1, 1 37B 650 2 1 541 80 75B 850 1 , 2 2 211 Courtesy of Steven Engineering, Inc.-230 Ryan Way, 258-9200-www.stevenengineering.com San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) South

72 176-AMF.qxd 10.5.7 11:10 AM Page 6 Compressed Air Cleaning Filter Series Made to Order Specifications 2 Please consult with SMC for detailed specifications, size and delivery. 3. With IN-OUT Flange 4. With Differential Pressure Gauge (GD40-2-01), IN-OUT Flange Makes flange piping easier when filter ports on IN and OUT are The differential pressure gauge is mounted on the main body to moni- flange connection. (Flange material: Carbon steel) tor the life of a filter by checking its clogging status. Ports on IN and OUT are flange connection type. (Flange material: Carbon steel) Specifications Specifications Applicable model AFF11C, 22C, 37B, 75B Applicable model AFF11C, 22C, 37B, 75B ∗ Refer to “How to Order” for standard ∗ Refer to “How to Order” for standard specifications. specifications. How to Order How to Order X17 X15 AFF AFF ∗ ∗ ∗ Body size Body size Option ∗ Option (Not applicable with ∗ ∗ (Not applicable with H) Thread type Thread type F, H, S, T, U, V) ∗ ∗ ∗ size Port Port size Auto drain ∗ Auto drain Specifications Specifications AM450C, 550C, 650, 850, AMD450C, 550C, 650, 850, AM450C, 550C, 650, 850, AMD450C, 550C, 650, 850, Applicable Applicable model model AMH450C, 550C, 650, 850, AMG450C, 550C, 650, 850 AMH450C, 550C, 650, 850 Refer to “How to Order” for standard ∗ ∗ Refer to “How to Order” for standard specifications. specifications. How to Order How to Order X15 X17 AM AM AMD AMD ∗ ∗ Option Option (Not applicable with (Not applicable with H) AMG AMH F, H, S, T, U, V) ∗ ∗ Body size Auto drain AMH ∗ Auto drain ∗ Thread type ∗ Body size ∗ size Port ∗ ∗ size Port Thread type The AMG series is not applicable since water drops could Note) • ingress inside its differential pressure gauge, resulting in Note) • Cannot be mounted to the AME and AMF series. (It malfunction or damage to the product. affects the cleanliness at the outlet.) • Cannot be mounted to the AME and AMF series. (It affects the cleanliness at the outlet.) Dimensions Dimensions A A Connection Connection C IN OUT OUT IN B B Drain port Drain port (mm) (mm) Series AFF Series AM, AMD, AMH Series AM, AMD, AMG, AMH Series AFF Connection Connection ABC AB JIS 10K FF flange JIS 10K FF flange Size Size Size Size 15 (1/2B) 3 242 ± 15 (1/2B) 242 ± 3 256 308 450C 11C 450C 11C 20 (3/4B) 239 3 ± 20 (3/4B) 239 ± 3 258 3 255 ± 20 (3/4B) 20 (3/4B) 3 ± 255 288 342 22C 550C 22C 550C 259 ± 4 25 (1B) 25 (1B) 259 ± 4 301 80 297 ± 4 25 (1B) 25 (1B) ± 4 297 345 394 37B 650 650 37B 1 1 324 ± 4 B) 40 (1 B) 40 (1 324 ± 4 352 2 2 1 1 ± 4 384 B) 40 (1 B) 40 (1 ± 384 4 489 2 2 541 850 75B 850 75B 378 4 ± 50 (2B) 50 (2B) 4 378 ± 497 212 CA Courtesy Engineering, Inc.-230 Ryan Way, South San Francisco, of Steven 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com

73 P0141-P0220-E.qxd 08.11.6 1:52 PM Page 213 Compressed Air Cleaning Filter Series Made to Order Specifications 3 Please consult with SMC for detailed specifications, size and delivery. 5. N.C., N.O. Auto Drain, Drain Piping Type 6. White Vaseline Specifications Changed the grease for O-rings and gaskets as lubricant to white Drain piping type (drain guide specification) to the drain exhaust from N.C. auto drain and N.O. auto drain. N.C. type is not available for the vaseline.  650. AFF37B and AM HAA Specifications Specifications HAW Applicable model Applicable model AFF2C to 22C, 37B AFF37B, 75B AT Refer to “How to Order” for standard Refer to “How to Order” for standard ∗ ∗ IDF specifications. specifications. How to Order How to Order IDU IDFA X26 X12 AFF AFF ∗ ∗ ∗ Body size Body size Option ∗ IDFB Option ∗ (Drain cock, drain guide and Thread type ∗ ∗ Thread type Auto drain F, H, V are not applicable.) ∗ ID Port size ∗ ∗ ∗ Accessory Port size Auto drain ∗ Accessory (Available for N.C., N.O. auto IDG drain only) Specifications Specifications AMG AM  150 to 650 Applicable model AM650, 850, AMD650, 850, AME650, 850, Applicable model AMF650, 850, AMG650, 850, AMH650, 850 AFF ∗ Refer to “How to Order” for standard ∗ Refer to “How to Order” for standard AM specifications. specifications. How to Order How to Order AMD X26 X12 AM AM AMH AMD AMD ∗ Option ∗ Option (Drain cock, drain guide and ∗ AMG AME AME Auto drain F, H, V are not applicable.) ∗ AMH AMF Accessory ∗ Auto drain AMF ∗ ∗ (Available for N.C., N.O. auto Body size Port size AMG drain only) ∗ Thread type SF ∗ Thread type ∗ AMH Accessory ∗ Port size ∗ Body size SFD Dimensions LLB  AD GD (A) 20 1/4 female threaded Drain (mm) Series AM, AMD, AMG, AMH Series AFF Port size A Size Size 1/8, 1/4 2C 150C 159 1/4, 3/8 4C 250C 172 3/8, 1/2 350C 8C 204 1/2, 3/4 450C 11C 225 3/4, 1 550C 22C 259 1 650 37B 1, 1 311 2 213 Courtesy of Steven Engineering, Inc.-230 258-9200-www.stevenengineering.com Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) Ryan

74 P0141-P0220-E.qxd 08.11.6 1:52 PM Page 214 Compressed Air Cleaning Filter Series Made to Order Specifications 4 Please consult with SMC for detailed specifications, size and delivery. 7. Mist Separator for High Flow Rate (0.3 μ m) Use this product when the conventional mist separator (Series AM) cannot dispose of a high flow rate. The specifications other than the nominal filtration rating are all equivalent to that of the AFF75A to 220A. Specifications Applicable model AFF75A to 220A Refer to “How to Order” for standard ∗ specifications. How to Order X13 AFF Standard size Accessory (Option) (Applicable compressor) Port size 214 Courtesy of Steven Engineering, Inc.-230 Ryan 258-9200-www.stevenengineering.com South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) Way,

75 5-2-18-AMF.qxd 10.1.14 2:21 PM Page 1 Compressed Air Cleaning Filter Series Special Specifications Please consult with SMC for detailed specifications, size and delivery. Clean Series (10-Series) Copper-free, Fluorine-free (20-Series) Clean Series products are used in cleaner environments such as in To eliminate effects on color CRTs, etc. by copper ion or fluorine clean rooms as compared to a general factory environment. For fur- resin, copper materials are electroless-nickel plated or changed to ther details, refer to the Clean Series catalog. copper-free materials to prevent the generation of copper ions. (It is not applicable to the AMD, AME, AMF and AMH series because those include fluorine resin in the filter material of the element.) HAA Specifications Specifications HAW AFF2C to 22C, 37B, 75B Applicable model Applicable model AFF2C to 22C, 37B AT ∗ Refer to “How to Order” for standard Refer to “How to Order” for standard ∗ specifications. specifications. IDF How to Order How to Order IDU C IDFA AFF AFF 10 J 20 D ∗ ∗ Body size Body size IDFB ∗ Note) Thread type ∗ Note 1) Thread type With drain guide Note) Option ∗ Port size ∗ Port size Note 2) Nil Option — ID Accessory IN-OUT — Nil Note) R Accessory Symbol Description reversal direction Rubber material: Fluororubber F IDG Symbol Description — Nil With element For medium air pressure (1.6 MPa) H T — Nil Bracket service indicator B IN-OUT reversal direction R Bracket B AMG “20-” is only applicable with N.C. auto drain (C) or N.O. auto drain (D). Note) With element service indicator T Drain cock and drain guide are copper-free, fluorine-free as standard. Note 2) Combination of F and T is not Note 1) “10-” is not applicable to AFF available. Specifications standard product (with F and H are only applicable to drain cock) and with Applicable model AFF75B the AFF2C to 22C. AM auto drain. 20 AFF75B Specifications AMD ∗ Applicable AM150C to 550C, 650, 850, AMD150C to 550C, 650, 850, Thread type model AMH150C to 550C, 650, 850 Option ∗ AMH size Port Nil — Accessory IN-OUT AM J 10 Description Symbol AME R reversal direction — Nil With element AMD Bracket B Note 1) T ∗ With drain guide Port size service indicator AMF N.O. auto drain D AMH Note 2) Option Specifications ∗ Body size SF — Nil ∗ Applicable model AM150C to 550C, 650, AMG150C to 550C, 650 Thread type Rubber material: Fluororubber F Note) SFD For medium air pressure (1.6 MPa) H Accessory C IN-OUT reversal direction R AM 20 Symbol Description D With element service indicator T — Nil LLB AMG Bracket Note 1) Note 2) Combination of F and T is not B ∗ Body size available.  AD ∗ Note 2) Thread type F and H are only applicable to Option Note 1) “10-” is not applicable to ∗ size Port 150C to 550C. the AM  Nil — standard product (with Accessory GD IN-OUT drain cock) and with R Description Symbol reversal direction auto drain. — Nil With element T service indicator Bracket B Specifications “20-” is only applicable with N.C. auto drain (C) or N.O. auto drain (D). Note 1) AME150C to 550C, 650, 850, Drain cock and drain guide are copper-free, fluorine-free as standard. Applicable model AMF150C to 550C, 650, 850 Note 2) R is only available for AMG. Specifications AME 10 AM850, AMG850 Applicable model AMF 850 AM 20 ∗ Body size ∗ Thread type AMG ∗ ∗ Port size Note) Thread type Option ∗ size Port Nil — Accessory Accessory Note) Option IN-OUT Symbol Description R Symbol Description reversal direction — Nil Nil — — Nil With element IN-OUT reversal direction R Bracket B T Bracket service indicator B Note) F and H are only applicable to the N.O. auto drain D AME, AMF150C to 550C. Note) R is only available for AMG. 215 Courtesy of Steven Engineering, Inc.-230 Ryan Way, South 258-9200-www.stevenengineering.com Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) San

76 176-AMF.qxd 10.5.7 11:10 AM Page 7 /AFF  AM Series Specific Product Precautions 1 Be sure to read before handling. Refer to front matters 42 and 43 for Safety Instructions and pages 6 to 8 for Air Preparation Equipment Precautions. Design Caution Warning 1. Hold the female thread side and tighten to the rec- 1. Design the layout so that the mist separator should ommended torque when screwing in the piping ma- be installed in an area that is less susceptible to terial. pulsations. Insufficient tightening torque may cause loosening or defec- The element could be damaged if a difference between the tive sealing. Over-tightening torque may damage the thread inlet pressure and the outlet pressure exceeds 0.1 MPa. etc. If it is tightened without holding the female thread side, 2. Be careful of dust generation by the pneumatic excessive force will be directly applied to the piping bracket equipment mounted on the outlet side. resulting in a product failure. When installing pneumatic equipment on the outlet side of the AM  series, dust particles may come off from outlet equip- Recommended Torque Unit: N · m ment, which will lower the cleanliness of compressed air. Con- Connection 1 1/8 1 3/4 1 2 1/2 1/4 3/8 2 sider this impact upon the cleanliness of compressed air when thread installing pneumatic equipment on the outlet side. Torque 12 to 14 28 to 30 28 to 30 36 to 38 48 to 50 48 to 50 1.5 to 2 7 to 9 ∗ After tightening manually, tighten additionally by about 1/6 turn with a 3. About when to use N.C. auto drain and N.O. auto tightening tool. drain. When using the AFF2C to 22C, 37B, 75B, AM  150C to 550C, 650, 850 with normally open (N.O.) auto drain, air may ceaselessly blow out of the drain discharge area when an air compressor with a small air discharge volume is used since the valve does not close unless the air pressure is 0.1 MPa or higher. Therefore, when using a compressor for 3.7 kW or less, make sure to use the normally closed (N.C.) auto drain. The minimum operating pressure is 0.15 MPa even with N.C. auto drain. 4. Use a tubing with proper size and length for drain piping of auto drain.  150C to 550C, 650 When using the AFF2C to 22C, 37B, AM with auto drain: 2. Do not apply torsional moment or bending moment Normally closed (N.C.) Use tubing O.D. 10 mm and keep (except the product's own weight) to the bracket. It Normally open (N.O.) the whole length within 5 m. may damage the bracket. Support external piping  When using the AFF75B and AM 850 with auto drain: separately. Normally open (N.O.): Use tubing I.D. 9 mm or more and keep the whole length within 2.8 m. 5. Provide a design that prevents back pressure and back flow. Back pressure or back flow may damage an element. 6. Keep the certificate of Class 2 Pressure Vessel in a safe place. Products below are subject to Class 2 Pressure Vessel Act. Certificate will be sent in 2 to 4 weeks later after the shipment of the product. Main Line Filter ················ AFF220A 0/9  0/10 1  Micro Mist Separator········ AMD9  3. Inflexible piping such as steel piping tends to be affected by spread of excessive moment load or vi- bration from the piping side. Lay flexible tubing be- tween the steel pipe and the product to prevent such effects. 216 Courtesy of Steven Engineering, Inc.-230 Ryan Way, South 258-9200-www.stevenengineering.com Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) San

77 176-AMF.qxd 10.5.7 11:10 AM Page 8  /AFF Series AM Specific Product Precautions 2 Be sure to read before handling. Refer to front matters 42 and 43 for Safety Instructions and pages 6 to 8 for Air Preparation Equipment Precautions. Selection Piping Caution Caution 1. Connect it with IN and OUT ports in proper location. HAA 1. About the system composition of purifying com- HAW It does not work with the connection reversed. pressed air In the case of the AFF2C to 22C, 37B, 75B, AM 150C to  Compressed air generally contains particulate contaminants AT 550C, 650, 850 as listed below, though there are some variations due to the compressor type and specifications. Determine the system Verify the direction of the flow of the compressed air and the IDF configuration according to the desired cleanliness of com- IDU “ ” or “ ” mark that indicates the inlet of the product before pressed air and application, while referring to the “Air Prepara- connecting. It cannot be used if connected in the opposite di- tion Equipment Selection Guide” (pages 2 and 3). rection. IDFA [Particulate contaminants in compressed air] Symbol which indicates the flow of IN • Water (drainage) compressed air IDFB • Dust sucked from ambient air or • Degenerated oil from compressor ID • Solid foreign matter such as rust inside piping and oil 2. Select according to the maximum flow consump- IDG tion. When compressed air is used for air blow, etc., find the maxi- OUT AMG  mum air consumption before selecting the size of the AM series. (If compressed air exceeding the maximum flow rate is supplied, it can result in decline of the cleanliness of com- AFF pressed air or element damage.) AM Mounting AMD AMH Caution 1. About the mounting orientation of the products AME Make sure to install this product on horizontal piping. If it is in- In the case of the AFF75A to 220A, AMD801, 901, 800, 900, stalled diagonally, laterally, or upside down, the drain separa- AMF 1000 ted by the element will splash to the outlet side. INLET and OUTLET of compressed air is labeled on the side of flange. Be sure to connect correctly. SF 2. Use an air blower to flush the piping before con- SFD necting the piping. Use an air blower to thoroughly flush the piping, or wash the LLB piping to remove any cutting chips, cutting oil, or debris from inside the piping before connecting them.  AD 3. Wrapping of sealant tape When screwing in the pipes or fittings, make sure to prevent cutting chips or the sealant material on the threaded portion of GD the pipe from entering the piping. If sealant tape is to be used, leave about 1.5 to 2 ridges of threads uncovered. 4. Modular connection Mount the attached bracket on one side when connecting 2 sets. Mount the attached brackets on both sides when con- necting 3 sets or more. As a guideline for the number of brackets, one bracket should be mounted for every 2 prod- ucts. 217 Courtesy of Steven Engineering, Inc.-230 Ryan Way, South 258-9200-www.stevenengineering.com Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) San

78 176-AMF.qxd 10.5.7 11:10 AM Page 9  Series AM /AFF Specific Product Precautions 3 Be sure to read before handling. Refer to front matters 42 and 43 for Safety Instructions and pages 6 to 8 for Air Preparation Equipment Precautions. Air Supply Maintenance Caution Caution 1. Replace the element immediately when the time for 1. The mist separator is not applicable to gases other its replacement has arrived. If the element is contin- than compressed air. ually used without replacement, there is a possibili- The mist separator is not applicable to gases other than com- pressed air (example: oxygen, hydrogen, flammable gas, ty of damage to the element. mixed gas). To replace the element, replace the O-ring and the gasket, too. For the replacement procedure, refer to the operating 2. Do not use compressed air that contains chemicals, manual. (For element dimensions, refer to page 219.) organic solvents, salt, or corrosive gases. Do not use compressed gas containing chemicals, organic a. In the case of the AFF2C to 22C, 37B, 75B, AM 150C to  solvents, salt or corrosive gas. This can cause rust, damage 550C, 650, 850 to rubber and resin parts, or malfunction. The replacement interval for the element is when the pressure 3. Operate within the specified operating pressure drop reaches 0.1 MPa or after two years of operation, which- range. ever comes first. A pressure drop can be verified with the ele- Damage, failure, or malfunction may occur if the mist separa- ment service indicator (-T) or with differential pressure gauge tor is operated above the maximum operating pressure. (Made to Order). If the mist separator is used below the minimum operating b. In the case of the AFF75A to 220A, AMD800 to 1000, pressure, increase in the air-flow resistance due to clogging AMD801, 901 will have such influence that the desired flow rate cannot be The replacement interval for the element is when the pressure obtained. drop reaches 0.1 MPa or after one year of operation, which- If the mist separator is used under a low pressure such as for ever comes first. Confirm the pressure drop with a pressure a blower, conduct sufficient tests by users to confirm the spec- gauge. (With pressure gauge: -G) ifications and performances. c. In the case of the AME Regardless of the time for its replacement indicated in “a” above, replace the element when a red color spot occurred on Operating Environment the surface. d. In the case of the AMF Caution Regardless of the time for its replacement indicated in “a” or 1. Do not use in the following environments, as this “b”, replace the element when you smell oil on the outlet side. can cause failure. 2. Be sure to exhaust the drain accumulated in the fil- 1) In locations having corrosive gases, organic solvents, and ter container. chemical solutions, or in locations where these elements Failure to discharge the drain will allow the accumulated drain are likely to adhere to the equipment. to flow over to the outlet side. 2) In locations where salt water, water, or water vapor could 150C to  When using the AFF2C to 22C, 37B, 75B, AM come in contact with the equipment. 550C, 650, 850 with drain cock, drain guide or ball valve, dis- 3) In locations that is exposed to shocks and vibrations. charge the drain before the drainage level reaches the center 2. Be careful about the contamination of the workpie- of the sight glass. If the drain is not discharged properly, it will flow over to the outlet side. ces due to entrainment of the ambient air. If compressed air is used for air blow, compressed air blowing out from the blow nozzle may entrain foreign matter (solid par- ticles and liquid particles) floating in the ambient air, blowing it Sight glass against the workpieces and causing adhesion. Therefore, suf- ficient precautions must be taken about the ambient environ- ment. Drainage level Discharge the drain before reaching the center level. 218 Courtesy of Steven Engineering, Inc.-230 Ryan Way, South 258-9200-www.stevenengineering.com Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) San

79 176-AMF.qxd 10.5.7 11:10 AM Page 10 /AFF  AM Series Specific Product Precautions 4 Be sure to read before handling. Refer to front matters 42 and 43 for Safety Instructions and pages 6 to 8 for Air Preparation Equipment Precautions. Maintenance Caution 5. The drain exhaust parts are different according to 3. In the case of a type with auto drain HAA HAW option or thread. • The auto drain operates when the drainage level reaches the top of the sight glass, and the drain will be discharged. Applicable models: AFF2C to 22C, AM, AMD, AMH, AMG150C AT to 550C 150C to 550C, • When using the AFF2C to 22C, 37B, AM  650 with auto drain, the drain is automatically discharged Thread type Drain exhaust IDF Option with the knob tightened to the “S” side. Manual drain dis- specifications Rc G NPT IDU charge, however, is also possible. AM-SA039 F, V Except AM-SA039-1 F IDFA Drain cock AM-SA039-2 V A manual knob attached to the auto drain end is tightened to AM-SA039-3 FV the “S” side in normal operation. The drain can be discharged IDFB AM-SA040 AM-SA040-F AM-SA040-N F, V Except by loosening it to the “O” side. (Be careful, however, if pres- AM-SA040-1 AM-SA040-F-1 AM-SA040-N-1 F sure remains inside the filter when the drain is discharged, the Drain guide AM-SA040-2 AM-SA040-F-2 AM-SA040-N-2 V ID drain will blow out from the drain port.) AM-SA040-3 AM-SA040-F-3 AM-SA040-N-3 FV AD53PA-D NAD53PA-D F, V Except N.C. IDG AD53PA-D-X155 NAD53PA-D-X155 F auto drain AD53PA-D-X113 NAD53PA-D-X113 V AD43PA-D NAD43PA-D F, H, V Except AMG N.O. AD43PA-D-X155 NAD43PA-D-X155 F auto drain AD43PA-D-X113 NAD43PA-D-X113 V AFF NAD33PA-D-X2004 AD33PA-D-X2004 EAD33PA-D-X2004 H AM Others OS AMD Caution Open Close AMH 1. Element interchange 4. The drain exhaust parts replacement method and Following is the element dimensions for the AFF and AM  necessary parts are different depending on when it AME series: was manufactured. Since elements for the same body size has the same dimen- sions, they are interchangeable. (When mounting the auto drain to drain cock and drain guide AMF However, do not interchange them easily since it can cause specified housing, mount by replacing the bowl assembly.) various kinds of problems. Necessary parts SF If interchanging the elements is unavoidable, replace the Manufactured Manufactured Manufactured product model number label, too. Descrip- Applicable Dec. 2003 or Jan. 2004 onwards Feb. 2010 onwards SFD tion size before [Up to [Manufacturing [Manufacturing lot No manufacturing lot No. IO to Note 2) OP to onwards] lot No. HZ] OO onwards] LLB Drain AM-SA039 AM-SA002 B cock  AD Thread type Rc: AM-SA003 Thread type Rc: AM-SA040 Drain 2C to 22C Thread type G: AM-SA003-F Thread type G: AM-SA040-F guide 2B to 37B Thread type NPT: AM-SA040-N Thread type NPT: AM-SA003-N GD 150C to 550C Auto drains cannot 150 to 650 Thread type Rc, G: AD43PA-D N.O. be replaced alone ø A since those cannot auto be assembled with- drain Thread type NPT: NAD43PA-D Element Dimensions out dedicated as- sembly tools. The Element dimensions 2C to 22C entire bowl assembly Thread type Rc, G: AD53PA-D N.C. (Reference value) Model must be replaced. 2B to 22B auto (Refer to “How to 150C to 550C AB ø Order Bowl Assem- drain Thread type NPT: NAD53PA-D 150 to 550 AFF2C, AFF2B, AM150C, AM150 bly” on page 206.) 49 42 Ball AMD150C, AMD150, AMH150C, AMH150 valve AM-SA004 AFF4C, AFF4B, AM250C, AM250 set 58 52 75B, 850 N.O. AMD250C, AMD250, AMH250C, AMH250 Thread type Rc, G: AD34PA-D auto Note 1) Thread type NPT: NAD34PA-D AFF8C, AFF8B, AM350C, AM350 drain 70 78 AMD350C, AMD350, AMH350C, AMH350 Note 1) Jig (AM-SA005) for replacing auto drain is necessary for the 75B or AFF11C, AFF11B, AM450C, AM450 850. 82 88 AMD450C, AMD450, AMH450C, AMH450 Note 2) When replacing parts with a production lot no. OP or after, order the parts with the same shape as the following figures. AFF22C, AFF22B, AM550C, AM550 96 118 AMD550C, AMD550, AMH550C, AMH550 AFF37B, AM650 122 144 AMD650, AMH650 AFF75B, AM850 Old drain cock New drain cock Old drain guide New drain guide 142 223 AMD850, AMH850 AM-SA039 AM-SA003 AM-SA002 AM-SA040 219 Courtesy of Steven Engineering, Inc.-230 Ryan Way, 258-9200-www.stevenengineering.com San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) South

80 176-AMF.qxd 10.5.7 11:10 AM Page 11 /AFF  Series AM Specific Product Precautions 5 Be sure to read before handling. Refer to front matters 42 and 43 for Safety Instructions and pages 6 to 8 for Air Preparation Equipment Precautions. Others Caution 2. About oil-free products 5. Internal volume of filter container The AFF and AM  series includes parts (such as resin parts, The product can be used as a small capacity air tank by re- rubber parts, and elements) that does not allow degreasing moving the element. wash. Therefore, oil-free products with all parts degreasing Following is the volume of filter containers of the AFF and washed is not available. series (when the element is removed). AM  3. Degreasing wash Volume Inside Filter Certain parts such as the body and housing can be degreas- ing washed. Contact SMC after confirming the specifications. Volume inside filter (available as Option or Made to Order) (Reference value) Model 3 (cm ) 4. Change of oil AFF2C, AFF2B, AM150C, AM150 series, no oil such as grease is applied  On the AFF and AM 250 AMD150C, AMD150, AMH150C, AMH150 to parts exposed to compressed air. However, for certain AFF4C, AFF4B, AM250C, AM250 specifications, there are some parts to which oil is applied. 300 AMD250C, AMD250, AMH250C, AMH250 It is possible to change the type of applied oil (as Option or AFF8C, AFF8B, AM350C, AM350 Made to Order). 600 AMD350C, AMD350, AMH350C, AMH350 AFF11C, AFF11B, AM450C, AM450 1000 AMD450C, AMD450, AMH450C, AMH450 AFF22C, AFF22B, AM550C, AM550 1500 AMD550C, AMD550, AMH550C, AMH550 AFF37B, AM650 3000 AMD650, AMH650 AFF75B, AM850 9000 AMD850, AMH850 Discontinued Model and Equivalent Model series were remodeled to products introduced in this catalog in 1988. The AFF and AM  Along with the new models, old models were provided mainly for the purpose of maintenance. However, due to the aging of metal d ies and extreme decline in the quantity, the procurement of parts and consequently the maintenance of the production system became diffi- cult. For this reason, old models were discontinued in 1994, as detailed in the table below. Use the equivalent model listed there. Discontinued Model and Equivalent Model Equivalent model Production discontinuance Period of production Period of External dimensions External dimensions discontinuance production Product name Model Model of product of product Page for maintenance discontinuance Width x Depth x Height Width x Depth x Height parts for products 76 x 76 x 175 AFF6 100 x 100 x 253 AFF4C 122 x 122 x 262 AFF22 150 x 140 x 446 AFF22C Main Line Filter P.153 160 x 160 x 314 AFF37 200 x 170 x 526 AFF37B 220 x 220 x 461 AFF55 280 x 280 x 497 AFF75B 63 x 63 x 161 AM200 63 x 63 x 191 AM150C 76 x 76 x 175 AM300 85 x 85 x 258 AM250C P.161 Mist Separator 90 x 90 x 207 AM400 120 x 120 x 236 AM350C 122 x 122 x 262 AM500 140 x 140 x 383 AM550C 160 x 160 x 314 AM600 180 x 170 x 465 AM650 63 x 63 x 161 AMD100 63 x 63 x 136 AMD150C End of March '99 End of July '94 76 x 76 x 175 AMD200 80 x 82 x 170 AMD250C 90 x 90 x 207 Micro Mist AMD300 90 x 90 x 233 AMD350C P.169 Separator 106 x 106 x 228 AMD400 140 x 140 x 380 AMD450C 122 x 122 x 262 AMD500 140 x 140 x 490 AMD550C 160 x 160 x 314 AMD600 140 x 140 x 590 AMD650 76 x 76 x 103 AMF200 80 x 80 x 153 AMF250C 90 x 90 x 132 AMF300 90 x 90 x 216 AMF350C Odor Removal P.195 106 x 106 x 151 AMF400 140 x 140 x 250 AMF450C Filter 122 x 122 x 187 AMF500 140 x 140 x 360 AMF550C 160 x 160 x 291 AMF600 140 x 140 x 460 AMF650 Note) Some models have different heights depending on the port size. They are shown in parentheses. 220 Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San 258-9200-www.stevenengineering.com CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) Francisco,

Related documents